Search
Use the search bar or filters below to find any TAPPI product or publication.
Filters
Content Type
Publications
Level of Knowledge
Collections
Journal articles
Magazine articles
The effect of microfibrillated cellulose on the wet-web strength of paper, TAPPI Journal January 2021
ABSTRACT: The wet-web strength of paper immediately after the press section of a paper machine is a critical factor in determining machine runnability. However, it is difficult to determine at commercial scale, because the web has to be broken and production interrupted in order to obtain a sample for measurement. The use of microfibrillated cellulose (MFC) is believed to increase wet-web strength, as it has allowed filler level increases of 10% or more on many commercial paper machines. In this paper, we describe a laboratory method for estimating the effect of MFC on wet sheet strength after press-ing, as well as actual measurements of wet-web strength from a pilot paper machine trial. These experiments have demonstrated the positive effect of MFC. At solids contents in the range typically observed after pressing, sheets with MFC at fixed filler content are significantly stronger, but also wetter, than those without it. When the use of MFC is combined with a typical increase in filler content, the wet web remains slightly stronger, but also becomes drier than the reference condition. These results are compatible with the theory put forward by van de Ven that wet-web strength is mainly a result of friction between entangled fibers, and they also suggest that the presence of MFC increases this friction.
Journal articles
Magazine articles
SetPoint: Ladies and Gentlemen, The Year You’ve Been Waiting For, Paper360º January/February 2021
SetPoint: Ladies and Gentlemen, The Year You’ve Been Waiting For, Paper360º January/February 2021
Journal articles
Magazine articles
Two Processes: Two Systems?, Paper360º January/February 2021
Two Processes: Two Systems?, Paper360º January/February 2021
Journal articles
Magazine articles
Recycling at Paper Mills: The Benefits of Water-Based Barrier Coatings, Paper360º January/February 2021
Recycling at Paper Mills: The Benefits of Water-Based Barrier Coatings, Paper360º January/February 2021
Journal articles
Magazine articles
COVID-19 Has Created New Opportunities for Tissue and Towel, Paper360º January/February 2021
COVID-19 Has Created New Opportunities for Tissue and Towel, Paper360º January/February 2021
Journal articles
Magazine articles
ASPI News, Paper360º January/February 2021
ASPI News, Paper360º January/February 2021
Journal articles
Magazine articles
Preparation of regenerated cellulose from rice straw lignocellulosic waste and its use for reinforced paper products, TAPPI Journal July 2021
ABSTRACT: Rice straw waste is a lignocellulosic waste produced by farmers in large quantities. In this study, regenerated cellulose (RC) from rice straw was prepared by dissolving rice straw holocellulose (HC) in NaOH/Urea/Thio-urea/Water solution by the freeze-thawing process. The crystallinity index of RC was calculated at 31%, which is out of the crystallinity range of 39%•69% that has been previously suggested.The study indicated that the RC is amorphous with a low degree of polymerization (638) and higher hydroxyl group content as compared to HC. The fiber length of RC was found to be 26.7% shorter; however, the width of RC was 21.2% higher as compared to HC. Reduced kinked fiber content was observed in the fraction of RC (18.3%) as compared with HC (39.1%), and a higher curl index of fiber was observed more so in HC (10.5%) than RC (5.6%). Because of the regeneration process, the fiber length was reduced and a fines element content of about 96% was observed in RC compared to the initial fines content of HC (56.9%). Irrespective of the high fines element content of RC, the composite paper of rice straw bleached pulp and RC fibers was developed with an increase in the tensile index from 41.4 N.m/g to 71.2 N.m/g and an increase in the burst index from 4.7 kPa.m2/g to 5.3 kPa.m2/g with the addition of 5% and 15% RC, respectively. However, enhanced tear index of paper was observed up to 5% and then it declined upon further addition of RC. The study revealed that regenerated cellulose can be used as a strength additive to overcome the shortcomings of low mechanical properties in paper products.
Journal articles
Magazine articles
Production of antimicrobial paper using nanosilver, nanocellulose, and chitosan from a coronavirus perspective, TAPPI Journal July 2021
ABSTRACT: The pulp and paper industry has an opportunity to play a vital role in breaking the spread of the COVID-19 pandemic through production that supports widespread use of antimicrobial paper. This paper provides a brief review of paper and paper-related industries, such as those producing relevant additives, and R&D organizations that are actively engaged in developing antimicrobial papers. The focus here is on the potential of three nano-additives for use in production of antimicrobial papers that combat coronavirus: nanosilver, nanocellulose, and chitosan. Various recent developments in relevant areas and concepts underlining the fight against coronavirus are also covered, as are related terms and concepts.
Journal articles
Magazine articles
Over the Wire..., Paper360º July/August 2021
Over the Wire..., Paper360º July/August 2021
Journal articles
Magazine articles
Smart and Resource-Efficient: The DNA of the Paper Industry, Paper360º July/August 2021
Smart and Resource-Efficient: The DNA of the Paper Industry, Paper360º July/August 2021