Search
Use the search bar or filters below to find any TAPPI product or publication.
Filters
Content Type
Publications
Level of Knowledge
Collections
Journal articles
Magazine articles
Application of foamed additives to the surface of wet handsheets, TAPPI Journal January 2021
ABSTRACT: We explored the application of foamed wet-end additives onto wet handsheets to qualify our method of application and to demonstrate the method’s usefulness for prescreening additives and foaming agents for packaging applications.We modified a laboratory drawdown coating machine to allow coating of wet handsheets with foamed additives. Initial sheet solids were adjusted to a target of 8%•25% by vacuum. Foam layer thickness was set mechanically. After application, the foamed additives were drawn into the sheet with vacuum. The additive dosage was adjusted by altering its concentration within the foaming formulation. We evaluated more than 100 foaming agents and 10 strength additives, comparing wet-end and foam-assisted addition with no addition on recycled linerboard and virgin linerboard furnish. Foam-assisted addition typically displayed a much steeper dose-response curve and much higher maximum strength levels than wet-end addition. Our results suggest potential target applications for this technology, such as lightweighting, and improved strength performance in mills with relatively closed water systems, where strength aids added into the wet end are adversely influenced by accumulation of inorganic ions and organic species.
Journal articles
Magazine articles
The effect of contact time between CPAM and colloidal silica on the flocculation behavior in the approach flow, TAPPI Journal January 2021
ABSTRACT: Multicomponent wet-end systems have become increasingly common in papermaking, with the objective of improving the retention-formation-dewatering relationship. It is quite common to use at least a cationic polymer, often in combination with an anionic microparticle. In some cases, a fixative is also used. However, there is still debate on the optimal implementation of these systems. In particular, optimizing the contact time of the cationic polymer prior to addition of the anionic microparticle is still poorly understood. In this work, we investigate the effect of the contact time of a cationic polyacrylamide (CPAM) prior to addition of colloidal silica on the flocculation response in a flowing fiber suspension. The effect of using a fixative is also investigated. Focused beam reflectance measurements (FBRM) are combined with zeta-potential measurements for optimizing the addition levels of a two- and three-component system, as well as for elucidating the effect of contact time on CPAM performance. Trials are then performed on a pilot scale flow loop, where the time between addition of these two components is varied and the resulting flocculation response is characterized using high-speed filming and image analysis techniques. It is shown that the efficacy of CPAM can be improved through use of a fixative and that a longer CPAM contact time may be beneficial in terms of immediate flocculation; however, hydrodynamic shear tends to dominate the flocculation response regardless of contact time due to floc rupture.
Journal articles
Magazine articles
Co-ground mineral/microfibrillated cellulose composite materials: Recycled fibers, engineered minerals, and new product forms, TAPPI Journal January 2021
ABSTRACT: When pulp and minerals are co-processed in suspension, the mineral acts as a grinding aid, allowing costeffective production of mineral/microfibrillated cellulose (MFC) composite materials. This processing uses robust milling equipment and is practiced at industrial scale. The resulting products can be used in many applications, including as wet- and dry-strength aids in paper and board production.Previously, we have reported that use of these MFC composite materials in fiber-based applications allow generally improved wet and dry mechanical properties with concomitant opportunities for cost savings, property improvements, or grade developments. Mineral/MFC composites made with recycled pulp feedstocks were shown to offer at least equivalent strength aid performance to composites made using virgin fibers. Selection of mineral and fiber allows preparation of mineral/MFC composites with a range of properties. For example, the viscosity of such formulations was shown to be controlled by the shape factor of the mineral chosen, effective barrier formulations were prepared, and mineral/MFC composites with graphite as the mineral were prepared.High-solids mineral/MFC composites were prepared at 75% total solids (37% fibril solids). When resuspended and used for papermaking, these high-solids products gave equivalent performance to never-dried controls.
Journal articles
Magazine articles
Coarse Filtration is the ´First Line of Defense’, Paper360º January/February 2021
Coarse Filtration is the ´First Line of Defense’, Paper360º January/February 2021
Journal articles
Magazine articles
TAPPI Journal Summaries, Paper360º January/February 2021
TAPPI Journal Summaries, Paper360º January/February 2021
Journal articles
Magazine articles
RMM Part 2: Belief-Driven Strategy, Paper360º January/February 2021
RMM Part 2: Belief-Driven Strategy, Paper360º January/February 2021
Journal articles
Magazine articles
Three-dimensional visualization and characterization of paper machine felts and their relationship to their properties and dewatering performance, TAPPI Journal July 2021
ABSTRACT: Polymeric felts are commonly used in the papermaking process on the paper machine wet end, in the press section, and in the dryer section. They provide an important function during paper manufacturing, including as a carrier or support; as a filter media assisting with water removal on the paper machine; in retention of fibers, fines, and fillers; and in some applications, such as tissue and towel, to impart key structural features to the web. These felts can have highly interwoven complex internal structures comprised of machine direction and cross-machine direction yarns of varying sizes and chemical compositions. Here, we present a non-intrusive three-dimensional (3D) image visualization method using advanced X-ray computed tomography (XRCT). This method was used to characterize the complex 3D felt structure and determine the water removal characteristics of some commonly used paper machine felts. The structural features analyzed include porosity; specific pore-yarn interfacial surface area; 3D pore size distribution; 3D fiber or yarn-size distribution; and their variations through the thickness direction. The top, middle, and bottom layers of the felt have very different structures to assist with water removal and impart paper properties. The size distribution of the yarns, as well as the pores in the different layers of the felt, are also inherently different. These structural features were non-intrusively quantified. In addition, variation in the structural characteristics through the thickness of the felts and its potential role in papermaking is explored. In addition to the 3D structural characteristics, permeability characteristics and water removal characteristics, including rewetting of select felt samples, have also been experimentally determined. It is interesting to observe the relationship between key structural features and permeability and water removal characteristics. These relationships can provide additional insights into press felt design, as well as ways to improve product properties and the dewatering efficiency and productivity of the paper machine.
Journal articles
Magazine articles
Uruguay Prepares to Open a Gateway to the World, Paper360º July/August 2021
Uruguay Prepares to Open a Gateway to the World, Paper360º July/August 2021
Journal articles
Magazine articles
The Paper360° 2021 TOP 50 POWER LIST, Paper360º July/August 2021
The Paper360° 2021 TOP 50 POWER LIST, Paper360º July/August 2021
Journal articles
Magazine articles
Thinking Beyond the Basement, Paper360º July/August 2021
Thinking Beyond the Basement, Paper360º July/August 2021