Search
Use the search bar or filters below to find any TAPPI product or publication.
Filters
Content Type
Publications
Level of Knowledge
Committees
Event Type
Collections
Journal articles
Last Word: Rumors and reality, SOLUTIONS! [01OCTSO80.pdf]
Rumors and reality, Solutions!, October 2001, Vol. 84(10)
Pigment Coating and Surface Sizing of Paper (second edition)
Pigment Coating and Surface Sizing of Paper (second edition)
Journal articles
Press fabric selection & performance improvement, Solutions!, October 2004, Vol. 87(10)
Press fabric selection & performance improvement, Solutions!, October 2004, Vol. 87(10) (52KB)
Magazine articles
New Name, New Vision for Mondiâ??s Office Papers, Solutions!, April 2005, Vol. 88(4) (251KB)
New Name, New Vision for Mondi’s Office Papers, Solutions!, April 2005, Vol. 88(4) (251KB)
Journal articles
Pre-damping effects on water absorption and drying dynamics in flexographic printing, TAPPI Journal November 2025
ABSTRACT: Optimizing flexographic printability can involve the ink and the substrate, as well as the printing process. It has been widely reported in the literature that controlling topography of the substrate and its porosity are vital for good flexographic printability, especially when using water-based inks. This study focuses on how pre-damping a surface impacts liquid absorption and improves wet trapping (ink on ink with no intermediate drying) in flexographic printing. A Prüfbau universal print tester was adapted to analyze flexographic wet-on-wet ink printing and trapping using yellow and magenta inks for contrast. Slow drying of the first ink layer (yellow) leads to mottle when the second layer (magenta) is applied. The study explores the “wet sponge” hypothesis: a pre-damped surface should absorb liquid faster. The Lucas- Washburn equation describes long-term absorption, but it does not capture short-term uptake, which instead follows a linear dependence on time.
Journal articles
A laboratory-scale automated vacuum-assisted device for coating of cellulose nanofibrils onto paper, TAPPI Journal November 2025
ABSTRACT: An automated vacuum-assisted coating system was developed to deposit cellulose nanofibril (CNF) layers onto paper substrates, simulating potential industrial geometries while allowing precise control of web speed (10•20 m/min), vacuum time (up to 30 s), and applicator gap (0.5•0.9 mm). Vacuum assistance makes it possible to obtain coat weights over 5 g/m2 in a single pass and increases solids after coating from less than 10% to over 28%• 30%, reducing drying demand by more than 60%. Coat weights were tuned from 6 to over 11 g/m² by varying suspension solids (0.4•0.6 wt%), line speed, and filtration length (20•40 mm), with strong agreement between experimental data and model predictions. Barrier testing showed Kit test values for double folded samples of 9•12 and Gurley air resistances above 4 × 104 s once coat weights exceeded 7 g/m². Comparable performance was achieved with lower fines content CNF (60%) by increasing coat weight, providing technical flexibility and cost advantages for industrial scale-up.
Journal articles
Influence of base sheet properties on barrier coating performance, TAPPI Journal November 2025
ABSTRACT: Paper packaging offers a sustainable alternative to standard plastic-based materials, particularly for food and beverage applications. With reduced fiber treatment options like fluorochemicals, uncoated base stock often provides little-to-no effective barrier against liquid water, oil/grease, or moisture transmission. Despite the lack of natural barrier performance, base sheet properties can significantly influence the efficiency of applied waterbased barrier coatings. In this study, various base stock properties, such as caliper, porosity, roughness, and ash content, are reported to influence the barrier performance of styrene-acrylic and a copolymer of styrene-butadiene/styrene-acrylate based barrier coatings. These findings will help paper and board producers design better, more cost-effective, purposebuilt substrates for barrier applications in the packaging industry.
Journal articles
Designing paper and board barrier constructions for food contact applications, TAPPI Journal November 2025
ABSTRACT: This study examines the effect of multiple factors on barrier performance for purpose-built paper and paperboard constructions produced on an industrial pilot coater machine. Impacts from precoat latex chemistry, application method (flooded nip with bevel blade, jet with bevel blade, and pre-metered film coater, laboratory rod drawdown) and precoating calendering were studied in relation to resulting porosity, roughness, and barrier (liquid water, moisture, and oil). Results reveal a complex interaction between controllable and uncontrollable factors, offering insight for designing advanced barrier coatings on cellulosic substrates.