Search
Use the search bar or filters below to find any TAPPI product or publication.
Filters
Content Type
Publications
Level of Knowledge
Collections
Journal articles
Magazine articles
Chemical addition to wet webs using foam application, TAPPI Journal January 2023
ABSTRACT: In papermaking, the conventional way to add chemicals to the web is to dose them into the fiber stock and form the paper afterwards. However, in many cases, adding chemicals directly to the stock is challenging. For example, strength aids tend to increase flocculation in the stock, which limits the addition amounts of those aids. The need for better performance of paper (and paperboard) products has given rise to the need for functionalization of paper. Adding such functional chemicals to the stock is usually rather inefficient. Hence, novel methods are needed to add chemicals to the paper bulk. One such method is dosing chemicals to the wet web via foam application. In this study, we built a laboratory-scale sheetfed dynamic foam application device and utilized it to study addition of starch to wet bleached chemithermomechanical pulp (BCTMP) paper handsheets. The impact of parameters such as vacuum level, the amount of added chemical, and the viscosity of the foaming liquid on the penetration of starch into the wet web was explored. Starch penetration into wet webs was measured via iodine-potassium iodide staining, followed by image analysis. According to our results, controlling the viscosity of the foaming liquid gives the best possibility to control the penetration.
Journal articles
Magazine articles
Z-direction chemical analysis for new application methods, TAPPI Journal January 2023
ABSTRACT: In conventional wet-end chemical addition during paper production, chemical distribution through the z-direction of the sheet is usually not considered an important characteristic. With a nontraditional chemical dosing approach, such as foam-assisted additive addition, the chemistry can appear at different concentrations throughout the sheet, typically in a z-direction gradient. To fully understand the strength properties of the sheet, it is helpful to view or quantify the chemical distribution through the sheet in the z-direction. One qualitative method uses a dye technique along with confocal laser scanning microscopy to generate an image where the relative chemical concentration can be observed. A quantitative method involves compiling nitrogen analyses of layered subsections of the sheet into a composite graph of relative chemical concentration vs. the z-direction of the sheet. Chemical distribution analysis can be paired with traditional z-direction strength tests, such as Scott bond and z-direction tensile, to help one understand and improve the chemical addition process and its effects.
Journal articles
Magazine articles
Pareto-based design of experiments for identifying and comparing optimum sealing parameters of heat sealing applications in packaging machines, TAPPI Journal June 2023
ABSTRACT: Sealing is one of the most important process steps in industrial packaging, because the sealed seam is the most sensitive section of a package in terms of quality. For this reason, a major focus in flexible packaging is the sealing process, and among this, heat sealing is the most frequently used technology. In detail, applications of heat sealing processes are confronted with four conflicting objectives: increasing seam quality, reducing dwell time, reducing sealing temperature, and increasing process robustness towards varying conditions. Typical problems, such as identification of the optimum process parameters or selection of the most appropriate packaging film, are subject to these conflicting objectives.This paper presents a recently published design of experiments for characterizing and comparing heat sealing properties of packaging films based on a multi-objective optimization algorithm. The approach provides easy-to-read charts showing all optimum sealing parameters with regard to the four essential objectives of heat sealing: seam quality, dwell time, sealing temperature, and process robustness. Three case studies show exemplary applications of the new approach: 1) analyzing transport damages of beverage powder packages; 2) identifying and comparing optimum sealing parameter of a standard, mono-material, and fiber based packaging film regarding tightness and visual properties of the produced sachets; and 3) analyzing the effect of additional aluminum layers on sealing characteristics regarding hot-tack.The new design of experiments may provide the basis of a standard test method for the identification of optimal sealing parameters in the heat sealing processes.
Journal articles
Magazine articles
Recovery boiler back-end heat recovery, TAPPI Journal March 2023
ABSTRACT: Sustainability and efficient use of resources are becoming increasingly important aspects in the operation of all industries. Recently, some biomass-fired boilers have been equipped with increasingly complex condensing back-end heat recovery solutions, sometimes also using heat pumps to upgrade the low-grade heat. In kraft recovery boilers, however, scrubbers are still mainly for gas cleaning, with only simple heat recovery solutions. In this paper, we use process simulation software to study the potential to improve the power generation and energy efficiency by applying condensing back-end heat recovery on a recovery boiler. Different configurations are considered, including heat pumps. Potential streams to serve as heat sinks are considered and evaluated. Lowering the recovery boiler flue gas temperature to approximately 65°C significantly decreases the flue gas losses. The heat can be recovered as hot water, which is used to partially replace low-pressure (LP) steam, making more steam available for the condensing steam turbine portion for increased power generation. The results indicate that in a simple condensing plant, some 1%•4% additional electricity could be generated. In a Nordic mill that provides district heating, even more additional electricity generation, up to 6%, could be achieved. Provided the availability of sufficient low-temperature heat sinks to use the recovered heat, as well as sufficient condensing turbine swallowing capacity to utilize the LP steam, the use of scrubbing and possibly upgrading the heat using heat pumps appears potentially useful.
Journal articles
Magazine articles
Non-process elements in the recovery cycle of six Finnish kraft pulp mills, TAPPI Journal March 2023
ABSTRACT: In this work, the aim was to study the distribution and accumulation of the non-process elements (NPEs) in the recovery cycle of Finnish pulp mills and look at whether the geographical location (North vs. South) correlates with the current Finnish NPE levels. In addition, a comparison to older similar Finnish measurements was made with an attempt to analyze the reasons behind differences in the most typical non-process elements, aluminum (Al), silicon (Si), calcium (Ca), phosphorus (P), magnesium (Mg), manganese (Mn), chlorine (Cl), and potassium (K), taking into account the main elements in the white liquor, sodium (Na) and sulfur (S). The extensive laboratory results gained in this study are from seven sampling points at six pulp mills and present analytical data of metal concentrations. The data obtained presents an update to previous NPE studies. The levels found did not statistically differ between North and South Finland. The NPE levels, apart from phosphorus, found in Finnish pulp mills today have not changed considerably compared to the levels in earlier investigations in the 1990s. In the newest data, the phosphorus concentration was consistently higher in the as fired black liquor, electrostatic precipitator (ESP) ash, lime mud, and green liquor than in the previous results. In addition, the levels of Al, Si, Ca, P, and Mg in recovery boiler ESP ash were consistently higher compared to the older results. As the mills start to close their systems more, a stronger accumulation of NPEs can be expected, increasing the likelihood of more operational problems in the process. Further understanding of where the NPEs accumulate and how they can be most effectively removed will be valuable knowledge in the future.
Journal articles
Magazine articles
Paper bending stiffness and web tension measurement from a running web using a vacuum and computer imaging, TAPPI Journal May 2023
ABSTRACT: A novel method for measuring the bending stiffness of paper online during manufacturing is introduced. The method uses photometric stereo imaging to detect the shape of the deflection surface caused by a controllable pressure difference over the paper’s surfaces. The hardware for the measurement is based on a combination of two existing sensors, which has accelerated and facilitated the development of the implementation. The deflection and loads are tied together by the governing differential equation for the bending of an orthotropic elastic plate with selected simplifications. An approach to resolve material parameters and in-plane loads without knowledge of traditional boundary conditions is suggested. The presented method was tested in a paper mill during manufacturing. For bending stiffnesses measured online, correlation coefficients 0.88 and 0.92 were obtained compared to state-of-the-art laboratory measurements. However, the results gained from a moving web are noisy and the data requires correction of the slope and an off-set. Although several issues remain to be resolved before the method can be considered as an accurate measurement for industrial use, the theoretical background, the performance of online implementation, and the results are promising. Possible causes for the observed discrepancies and the future development of the method are discussed.
Journal articles
Magazine articles
Modeling and parameter optimization of the papermaking processes by using regression tree model and full factorial design, TAPPI Journal February 2021
ABSTRACT: One of the major challenges in the pulp and paper industry is taking advantage of the large amount of data generated through its processes in order to develop models for optimization purposes, mainly in the papermaking, where the current practice for solving optimization problems is the error-proofing method. First, the multiple linear regression technique is applied to find the variables that affect the output pressure controlling the gap of the paper sheet between the rod sizer and spooner sections, which is the main cause of paper breaks. As a measure to determine the predictive capacity of the adjusted model, the coefficient of determination (R2) and s values for the output pressure were considered, while the variance inflation factor was used to identify and eliminate the collinearity problem. Considering the same amount of data available by using machine learning, the regression tree was the best model based on the root mean square error (RSME) and R2. To find the optimal operating conditions using the regression tree model as source of output pressure measurement, a full factorial design was developed. Using an alpha level of 5%, findings show that linear regression and the regression tree model found only four independent variables as significant; thus, the regression tree model demonstrated a clear advantage over the linear regression model alone by improving operating conditions and demonstrating less variability in output pressure. Furthermore, in the present work, it was demonstrated that the adjusted models with good predictive capacity can be used to design noninvasive experiments and obtain.
Journal articles
Magazine articles
Editorial: Agility and adaptation in a dynamic business world, TAPPI Journal January 2021
ABSTRACT: Being agile and adaptive in this current business world is both necessary and beneficial. Throughout last year, we all continued to both directly and indirectly experience the dynamic world where we live. As we wll know, in early 2020 the pandemic gained momentum and has fundamentally altered our daily lives, both personally in how we live and professionally in how we work.
Journal articles
Magazine articles
Spraying starch on the Fourdrinier— An option between wet end starch and the size press, TAPPI Journal January 2021
ABSTRACT: Technology to apply suspensions of starch grains to the wet surface of paper, during the dewatering process, is reviewed. Though the technology is not new, it continues to attract the attention of papermakers as a means to increase bonding strength. Starch grains that are sprayed onto the wet-web of paper can be retained at levels exceeding what can be effectively added to the fiber suspension at the wet end. Unlike adding a starch solution at a size press, no additional drying capacity is required on the paper machine. To be effective, the starch needs to be able to swell and develop bonding during the paper drying process. Paperboard applications with recycled fibers appear to be a good fit. There is potential to increase bonding by processes that favor fuller gelatinization of the starch grains by the time the paper becomes dry.
Journal articles
Magazine articles
Understanding wet tear strength at varying moisture content in handsheets, TAPPI Journal January 2021
ABSTRACT: A laboratory study was conducted looking at the effects of moisture content on wet tear strength in handsheets. Three different wetting techniques were used to generate the wet tear (Elmendorf-type) data at varying moisture levels, from TAPPI standard conditions (dry) to over 60% moisture content (saturated). Unbleached hardwood and softwood fiber from full-scale kraft pulp production were used. The softwood fiber was refined using a Valley beater to reduce freeness. Handsheets were made with a blend of hardwood and softwood and with refined softwood, without the addition of wet-end chemistry. The resulting grams-force tear data obtained from the test was indexed with basis weight and plotted versus both moisture content and dryness. As moisture content levels in the handsheets increased, the wet tear strength also increased, reaching a critical maximum point. This marked a transition point on the graph where, beyond a critical moisture content level, the tear strength began to decline linearly as moisture increased. This pattern was repeated in handsheets made from a blend of hardwood and softwood and from 100% refined softwood.