Search
Use the search bar or filters below to find any TAPPI product or publication.
Filters
Content Type
Publications
Level of Knowledge
Committees
Collections
Web instability in the open draw and the impact on paper machine efficiency, TAPPI Journal May 2022
ABSTRACT: Paper is most likely to break in the first open draw on a paper machine where it is unsupported, wettest, and weakest. Tension is applied to peel the web from the roll surface, as well as minimize web flutter in the open draw. The average tension is well below the breaking point and is often set by adjusting the speed difference between the press and the next machine element by visually observing the behavior of the web. However, machine direction variations caused by instabilities in the paper machine can cause tension swings that exceed the strength of the web. Measurement of the web’s release point from press rolls on pilot and commercial paper machines was used to identify the cause of tension instabilities. Variations in the speed of the paper machine drives and the work of adhesion from the press roll surface were identified as key factors. Fluctuations of paper moisture, which affects the elastic modulus and strength of the web, appear to be less important.
Effects of rings on flow and temperature in lime kilns, TAPPI Journal June 2022
ABSTRACT: A steady state, two-dimensional (2D) axisymmetric model has been developed to help understand how rings form and grow in a typical lime kiln. Rings of varying length, thickness, and geometry at the front and back faces were modeled to study the effects on flue gas flow and temperature. The results show that ring growth causes the gas velocity to increase and insulates the adjacent refractory, resulting in a lower kiln shell temperature. The results also reveal the formation of recirculation zones immediately down-stream of the rings, as well as temperature deviations upstream and downstream of the rings that might promote recarbonation and further ring growth. The model was applied to a kiln from a kraft mill with front-end and mid-kiln rings and good agreement was obtained between the measured and predicted kiln shell temperatures, providing confidence in the modeling.
Editorial: TAPPI’s 2022 Nanotechnology Conference convenes in Finland, TAPPI Journal June 2022
ABSTRACT: TAPPI’s International Conference on Nano-technology for Renewable Materials was finally held in person this past June 13-17 in Helsinki, and more than 200 attendees gathered to participate in the 36-session program. A total of 24 countries were represented at the event and more than one-third of attendees were first-time participants.
The Influence of the Fine Structure of Cellulose on the Action of Cellulases, TAPPI Journal June 2022
ABSTRACT: In the hydrolysis of cellulose with enzymes of Aspergillus niger at 47°C., it shown that a great decrease in the rate occurred in the late stage of the reaction, usually with considerable cellulose still reamaining undissolved.
Journal articles
Effects of localized environment on eucalyptus clone chemica
Effects of localized environment on eucalyptus clone chemical composition, TAPPI JOURNAL September 2016
Journal articles
Acoustic analysis of recovery boiler dissolving tank operati
Acoustic analysis of recovery boiler dissolving tank operation and smelt shattering efficiency, TAPPI JOURNAL September 2016
Journal articles
Editorial: PEERS 2016 honors technical achievements, TAPPI J
Editorial: PEERS 2016 honors technical achievements, TAPPI JOURNAL September 2016
Journal articles
Fast evaluation of spatial coating layer formation using ultraviolet scanner imaging
Fast evaluation of spatial coating layer formation using ultraviolet scanner imaging, TAPPI JOURNAL August 2015
Effects of orders of addition in nanocellulose–cationic starch– colloidal silica systems for papermaking, TAPPI Journal October 2022
ABSTRACT: Two orders of addition were compared when preparing paper handsheets from recycled copy paper furnish in combination with nanofibrillated cellulose (NFC), cationic starch, colloidal silica, and cationic retention aid (cPAM; cationic polyacrylamide). Faster dewatering and higher fine-particle retention were obtained at equal optimized dosages of additives when the colloidal silica was added last, after addition of the cPAM. The same order of addition also provided a higher gain in the paper’s tensile strength. However, higher paper stiffness was achieved when the colloidal silica was instead added to the NFC, after its pretreatment with cationic starch. Results were consistent with the principle that papermaking additives added shortly before sheetforming tend to have the largest effects on drainage and retention. The results also demonstrated a sensitivity to the relative dosages of positively and negatively charged additives.
Research on improving the basis weight measurement accuracy of tissue paper based on PSO-BP neural network, TAPPI Journal October 2022
ABSTRACT: The near-infrared (NIR) sensor can be used for measuring the basis weight and moisture of tissue paper, but the measurement accuracy is not ideal for this paper grade. The weight range of the tissue is 10~30 g/m2, indicating that it is a low gram weight paper. The temperature and humidity of the production environment significantly impact an NIR sensor. This paper focuses on improving the measurement accuracy of tissue paper basis weight. In order to reduce the influences of temperature and humidity, a mathematical model based on a particle swarm optimization back propagation (PSO-BP) neural network is proposed. In comparison with multiple linear regression measurement models, the basis weight measurement error with the PSO-BP model is within ± 0.5 g/m2. This model can effectively improve the measurement accuracy and has a good effect on overcoming the basis weight nonlinear effect caused by the changes in ambient temperature and humidity.