Search
Use the search bar or filters below to find any TAPPI product or publication.
Filters
Content Type
Publications
Level of Knowledge
Collections
Journal articles
Magazine articles
Evaluation of rice straw for purification of lovastatin, TAPPI Journal November 2021
ABSTRACT: Cholesterol synthesis in the human body can be catalyzed by the coenzyme HMG-CoA reductase, and lovastatin, a key enzyme inhibitor, can reduce hypercholesterolemia. Lovastatin can be obtained as a secondary metabolite of Aspergillus terreus ATCC 20542. In this study, rice straw of lignocellulose was used in aeration and agitation bath fermentation in a 1-L flask, and a maximal crude extraction rate of 473 mg/L lovastatin was obtained. The crude extract was treated with silica gel (230–400 mesh) column chromatography. Ethyl acetate/ethanol (95%) was used as the mobile phase, and isolation was performed through elution with various ethyl acetate/ethanol ratios. The highest production rate of 153 mg/L was achieved with ethyl acetate/ethanol in a ratio of 8:2. The lovastatin gained from the crude extract was added to 12 fractions treated with 0.001 N alkali, and acetone was then added. After 24 h of recrystallization at 4°C, the extract underwent high-performance liquid chromatography. The purity had increased from 25% to 84.6%, and the recovery rate was 65.2%.
Journal articles
Magazine articles
Repulping of wet strength paper towel with potassium monopersulfate, TAPPI Journal September 2020
ABSTRACT: Potassium monopersulfate (KMPS) was used in repulping of polyamide-epichlorohydrin (PAE)-containing paper towel. The effectiveness of the repulping aid was compared with that of sodium hypochlorite. Addition of a 2.4% KMPS repulping aid achieved complete repulping of the paper towel, resulting in 88% screen yield and about 5% rejects. To reach a similar pulping result, two times the oxidative equivalent amount of sodium hypochlorite had to be used. Compared to the pulp fibers obtained from sodium hypochlorite repulping, those obtained from KMPS repulping had higher physical strength, longer fiber length, and lower fines content. This study demonstrated that KMPS was superior to sodium hypochlorite in repulping of PAE-containing paper towel in terms of effectiveness and pulp quality.
Journal articles
Magazine articles
How do mud balls form in lime kilns?, TAPPI Journal April 2023
ABSTRACT: Mud ball formation in lime kilns has been a persistent problem in many kraft mills, particularly for older kilns that are equipped with chains. A systematic laboratory study was conducted to examine how mud balls are formed and the key factors that affect ball formation. The results confirm the general mill experience that high moisture and high sodium contents in lime mud are the main contributing factors to ball formation. The high moisture content allows lime mud to agglomerate and grow to form balls, while the high sodium content helps make the balls hard and retain their shape. A ball formation mechanism is proposed to explain how mud balls form and grow near the kiln feed end.
Journal articles
Magazine articles
Does the kappa number method accurately reflect lignin content in nonwood pulps?, TAPPI Journal November 2018
Does the kappa number method accurately reflect lignin content in nonwood pulps?, TAPPI Journal November 2018
Journal articles
Magazine articles
Fate of phosphorus in the recovery cycle of the kraft pulping process, TAPPI Journal March 2020
ABSTRACT: The accumulation of nonprocess elements in the recovery cycle is a common problem for kraft pulp mills trying to reduce their water closure or to utilize biofuels in their lime kiln. Nonprocess elements such as magnesium (Mg), manganese (Mn), silicon (Si), aluminum (Al), and phosphorus (P) enter the recovery cycle via wood, make-up chemicals, lime rock, biofuels, and process water. The main purge point for these elements is green liquor dregs and lime mud. If not purged, these elements can cause operational problems for the mill. Phosphorus reacts with calcium oxide (CaO) in the lime during slaking; as a result, part of the lime is unavailable for slaking reactions. The first part of this project, through laboratory work, identified rhenanite (NaCa(PO4)) as the form of P in the lime cycle and showed the negative effect of P on the availability of the lime. The second part of this project involved field studies and performing a mass balance for P at a Canadian kraft pulp mill.
Journal articles
Magazine articles
Combustion behavior of kraft black liquor droplets from hot
Combustion behavior of kraft black liquor droplets from hot water pretreated hardwood and softwood chips, November 2016 TAPPI JOURNAL
Journal articles
Magazine articles
Editorial: TAPPI Journal Best Research Paper for 2023 focuses on black liquor concentration using graphene oxide membranes, TAPPI Journal February 2024
ABSTRACT: TAPPI and the TAPPI Journal (TJ) Editorial Board would like congratulate the authors of the 2023 TAPPI Journal Best Research Paper Award and Honghi Tran Prize: Sam Rae, Ella V. Richards, Max Kleiman-Lynch, Brent D. Keller, and Brandon I. Macdonald. Their paper, “Pilot scale black liquor concentration using pressure driven membrane separation,” appeared on p. 223 of the April 2023 issue. This kraft recovery cycle research was recognized by the TAPPI Journal Editorial Board for its innovation, creativity, scientific merit, and clear expression of ideas.
Journal articles
Magazine articles
Effects of varying total titratable alkali and causticizing efficiency targets on kraft pulp mill productivity, TAPPI Journal March 2024
ABSTRACT: The kraft mill causticizing area is often overlooked and undervalued when it comes to mill optimization; however, the operation of the causticizing plant has downstream effects on the entire liquor cycle. Setting the right targets for the causticizing plant can have a tremendous effect on mill operating costs, as well as push the production bottleneck from one unit operation to another. The key performance parameters associated with the causticizing plant itself are liquor total titratable alkali (TTA) and causticizing efficiency. Individual facilities choose their TTA and causticizing efficiency targets based on their goals, the limits of their equipment, and past experiences. This gives a variety of operating strategies in practice, but what are the implications for optimizing total titratable alkali and causticizing efficiency, and what level of optimization can be achieved through implementation of modern technology? This paper reviews the results of several different operational strategies and models the effects of these different approaches on kraft mill liquor cycle.
Journal articles
Magazine articles
Tetraethyl orthosilicate-containing dispersion coating — water vapor and liquid water barrier properties, TAPPI Journal September 2021
ABSTRACT: An aqueous styrene-butadiene latex dispersion coating containing in-situ processed tetraethyl orthosilicate (TEOS) applied on paperboard demonstrated improved water barrier performance. Coatings containing TEOS equivalent to 0.8% silicon dioxide (SiO2; dry basis) exhibited water vapor performance of < 25 g/m2/day (23°C, 50% relative humidity [RH]) and liquid water barrier performance Cobb 1800 s of < 6 g/m2, when applied as a single-layer 18 g/m2 coating. Cobb 1800 s barrier performance was still good (< 11 g/m2) at coat weights of 7–10 g/m2. The use of filler materials such as kaolin improved the vapor barrier properties of the coating, but this was not critical to the liquid water barrier properties.
Journal articles
Magazine articles
Fate of phosphorus in the recovery cycle of the kraft pulping process, TAPPI Journal March 2020
ABSTRACT: The accumulation of nonprocess elements in the recovery cycle is a common problem for kraft pulp mills trying to reduce their water closure or to utilize biofuels in their lime kiln. Nonprocess elements such as magnesium (Mg), manganese (Mn), silicon (Si), aluminum (Al), and phosphorus (P) enter the recovery cycle via wood, make-up chemicals, lime rock, biofuels, and process water. The main purge point for these elements is green liquor dregs and lime mud. If not purged, these elements can cause operational problems for the mill. Phosphorus reacts with calcium oxide (CaO) in the lime during slaking; as a result, part of the lime is unavailable for slaking reactions. The first part of this project, through laboratory work, identified rhenanite (NaCa(PO4)) as the form of P in the lime cycle and showed the negative effect of P on the availability of the lime. The second part of this project involved field studies and performing a mass balance for P at a Canadian kraft pulp mill.