Search
Use the search bar or filters below to find any TAPPI product or publication.
Filters
Content Type
Publications
Level of Knowledge
Committees
Collections
Journal articles
Magazine articles
Recovery boiler back-end heat recovery, TAPPI Journal March 2023
ABSTRACT: Sustainability and efficient use of resources are becoming increasingly important aspects in the operation of all industries. Recently, some biomass-fired boilers have been equipped with increasingly complex condensing back-end heat recovery solutions, sometimes also using heat pumps to upgrade the low-grade heat. In kraft recovery boilers, however, scrubbers are still mainly for gas cleaning, with only simple heat recovery solutions. In this paper, we use process simulation software to study the potential to improve the power generation and energy efficiency by applying condensing back-end heat recovery on a recovery boiler. Different configurations are considered, including heat pumps. Potential streams to serve as heat sinks are considered and evaluated. Lowering the recovery boiler flue gas temperature to approximately 65°C significantly decreases the flue gas losses. The heat can be recovered as hot water, which is used to partially replace low-pressure (LP) steam, making more steam available for the condensing steam turbine portion for increased power generation. The results indicate that in a simple condensing plant, some 1%•4% additional electricity could be generated. In a Nordic mill that provides district heating, even more additional electricity generation, up to 6%, could be achieved. Provided the availability of sufficient low-temperature heat sinks to use the recovered heat, as well as sufficient condensing turbine swallowing capacity to utilize the LP steam, the use of scrubbing and possibly upgrading the heat using heat pumps appears potentially useful.
Journal articles
Magazine articles
Non-process elements in the recovery cycle of six Finnish kraft pulp mills, TAPPI Journal March 2023
ABSTRACT: In this work, the aim was to study the distribution and accumulation of the non-process elements (NPEs) in the recovery cycle of Finnish pulp mills and look at whether the geographical location (North vs. South) correlates with the current Finnish NPE levels. In addition, a comparison to older similar Finnish measurements was made with an attempt to analyze the reasons behind differences in the most typical non-process elements, aluminum (Al), silicon (Si), calcium (Ca), phosphorus (P), magnesium (Mg), manganese (Mn), chlorine (Cl), and potassium (K), taking into account the main elements in the white liquor, sodium (Na) and sulfur (S). The extensive laboratory results gained in this study are from seven sampling points at six pulp mills and present analytical data of metal concentrations. The data obtained presents an update to previous NPE studies. The levels found did not statistically differ between North and South Finland. The NPE levels, apart from phosphorus, found in Finnish pulp mills today have not changed considerably compared to the levels in earlier investigations in the 1990s. In the newest data, the phosphorus concentration was consistently higher in the as fired black liquor, electrostatic precipitator (ESP) ash, lime mud, and green liquor than in the previous results. In addition, the levels of Al, Si, Ca, P, and Mg in recovery boiler ESP ash were consistently higher compared to the older results. As the mills start to close their systems more, a stronger accumulation of NPEs can be expected, increasing the likelihood of more operational problems in the process. Further understanding of where the NPEs accumulate and how they can be most effectively removed will be valuable knowledge in the future.
Journal articles
Magazine articles
Editorial: Shaping industry and career success with TAPPI Standards involvement, TAPPI Journal May 2023
ABSTRACT: Within TAPPI, there are many ways to help advance our industry and make sure it thrives for years to come. Writing a research paper for publication or acting as peer reviewer for TAPPI Journal, presenting at a conference or helping to organize one, and becoming involved in the many committees that are part of TAPPI Divisions are just some of the ways. One other very important way to contribute to our industry is through the standards development process.
Journal articles
Magazine articles
Comparative analysis and benchmarking of commercial and emerging fast pyrolysis technologies, TAPPI Journal May 2023
ABSTRACT: It is well established that producing sustainable fuels and replacing the fossil-based ones is one of the key solutions to achieving net-zero emissions goals. One of the most advanced commercial-scale pathways to biofuels available today is fast pyrolysis. However, due to the need for a supportive regulatory environment and mitigation strategies for uncertainties related to costs and feedstock quality, fast pyrolysis is not yet being widely implemented. In this case study, three fast pyrolysis technologies with a technology readiness level (TRL) of 6 and above have been compared to distinguish between them and identify the conditions under which they are economically viable. The circulating fluidized bed (CFB), rotating cone (RC), and mechanically assisted fluidized bed (MFB) fast pyrolysis technologies were considered. First, the flow diagram and a mass and energy balance comparison were addressed. It was revealed that the RC configuration has better bio-oil yields because it can handle smaller particles. The MFB configuration has a progressive condensation unit at the end of the process, which produces a nearly dry oil having a higher energy content. Four implementation scenarios were studied. The first was the fast pyrolysis standalone process, where all options had marginal economic attractiveness, and the RC configuration economically outperformed the other two. Integration of a fast pyrolysis plant into a sawmill in the second scenario was found to bring significant improvements in revenues and internal rate of return (IRR). Realization of the full value of bio-oil (the third scenario) brought significantly more revenues for the MFB. Finally, the fourth scenario involved adding a progressive condensation unit, which increased the capital expenditure (CAPEX) by 3%•4% while increasing revenues by 32%•35%. A sensitivity analysis highlighted the importance of financial support towards capital cost and the full valuation of bio-oil for the economic viability of fast pyrolysis processes. Progressive condensation leading to more added-value bio-oil makes the standalone fast pyrolysis process more profitable.
Journal articles
A laboratory-scale automated vacuum-assisted device for coating of cellulose nanofibrils onto paper, TAPPI Journal November 2025
ABSTRACT: An automated vacuum-assisted coating system was developed to deposit cellulose nanofibril (CNF) layers onto paper substrates, simulating potential industrial geometries while allowing precise control of web speed (10•20 m/min), vacuum time (up to 30 s), and applicator gap (0.5•0.9 mm). Vacuum assistance makes it possible to obtain coat weights over 5 g/m2 in a single pass and increases solids after coating from less than 10% to over 28%• 30%, reducing drying demand by more than 60%. Coat weights were tuned from 6 to over 11 g/m² by varying suspension solids (0.4•0.6 wt%), line speed, and filtration length (20•40 mm), with strong agreement between experimental data and model predictions. Barrier testing showed Kit test values for double folded samples of 9•12 and Gurley air resistances above 4 × 104 s once coat weights exceeded 7 g/m². Comparable performance was achieved with lower fines content CNF (60%) by increasing coat weight, providing technical flexibility and cost advantages for industrial scale-up.
Journal articles
Editorial: Coating innovations for driving the next generation of sustainable packaging, TAPPI Journal November 2025
Welcome to the 2025 Special Coating Issue of TAPPI Journal. As we reflect on developments in 2025, the industry’s focus on sustainable packaging continues to sharpen, bringing several critical coating challenges and opportunities into view.
Journal articles
Influence of base sheet properties on barrier coating performance, TAPPI Journal November 2025
ABSTRACT: Paper packaging offers a sustainable alternative to standard plastic-based materials, particularly for food and beverage applications. With reduced fiber treatment options like fluorochemicals, uncoated base stock often provides little-to-no effective barrier against liquid water, oil/grease, or moisture transmission. Despite the lack of natural barrier performance, base sheet properties can significantly influence the efficiency of applied waterbased barrier coatings. In this study, various base stock properties, such as caliper, porosity, roughness, and ash content, are reported to influence the barrier performance of styrene-acrylic and a copolymer of styrene-butadiene/styrene-acrylate based barrier coatings. These findings will help paper and board producers design better, more cost-effective, purposebuilt substrates for barrier applications in the packaging industry.
Journal articles
Designing paper and board barrier constructions for food contact applications, TAPPI Journal November 2025
ABSTRACT: This study examines the effect of multiple factors on barrier performance for purpose-built paper and paperboard constructions produced on an industrial pilot coater machine. Impacts from precoat latex chemistry, application method (flooded nip with bevel blade, jet with bevel blade, and pre-metered film coater, laboratory rod drawdown) and precoating calendering were studied in relation to resulting porosity, roughness, and barrier (liquid water, moisture, and oil). Results reveal a complex interaction between controllable and uncontrollable factors, offering insight for designing advanced barrier coatings on cellulosic substrates.
Journal articles
The industry is entering a pivotal moment in which many of us find ourselves engaged in deep soul searching. Since the days of Francis Bacon when the illustrious triumvirate of gunpowder, the compass, and paper were the drivers of civilizations, our commu
The industry is entering a pivotal moment in which many of us find ourselves engaged in deep soul searching. Since the days of Francis Bacon when the illustrious triumvirate of gunpowder, the compass, and paper were the drivers of civilizations, our community has enjoyed a noble place at the table. Indeed, especially over the last 100 years, pulp and paper has quietly powered communication, commerce, and, more than ever today, packaging, thus representing a steady backbone for the continued stability of many global industries.
Journal articles
ABSTRACT: Laboratory experiments with bleached kraft furnish were carried out to quantify the effects of major differences in electrical conductivity of papermaking process water (due to the addition of sodium sulfate) on the performance of various paperm
ABSTRACT: Laboratory experiments with bleached kraft furnish were carried out to quantify the effects of major differences in electrical conductivity of papermaking process water (due to the addition of sodium sulfate) on the performance of various papermaking additives. Batches of refined pulp were prepared with conductivity levels of 168 (tap water), 1000, and 10,000 ìS/cm. The absolute values of the calculated zeta potential, in various cases, were shown to decrease with increasing logarithm of electrical conductivity. The performance of retention aid systems, including cationic polyacrylamide (cPAM), were not adversely affected by increased salinity, even up to an electrical conductivity level of 10,000 ìS/cm. In fact, treatment involving sequential addition of cPAM and colloidal silica showed superior retention of mineral filler at the highest conductivity level. Likewise, combinations of papermaking additives that promote the dewatering of paper continued to perform well in furnish prepared with increasing salinity. The ability of various chemical systems to induce flocculation among papermaking fibers decreased moderately at the highest level of salinity considered.