Search
Use the search bar or filters below to find any TAPPI product or publication.
Filters
Content Type
Publications
Level of Knowledge
Committees
Event Type
Collections
Journal articles
Black liquor spray properties in-furnace conditions for swirl cone nozzles, TAPPI Journal July 2026
ABSTRACT: Recovery boiler furnace operation is controlled for high chemical recovery, high steam production, and low emissions. Good control allows long runs with minimum cleaning without expensive shutdowns. An essential variable affecting boiler operation is black liquor spraying into the furnace. Poorly controlled black liquor spraying causes difficulties, e.g., in chemical recovery, fouling of heat transfer surfaces, and decreased energy production. A challenging measurement strategy with three different swirl cone nozzles . types A, C, and T . was carried out at a mill in the United States. Black liquor spray properties were measured under in-furnace conditions for flow rates of 2.0 L/s to 3.0 L/s. Three spraying temperatures of 119™‹C, 122™‹C, and 126™‹C, which were 2™‹C, 5™‹C, and 9™‹C above the boiling point (ƒ¢Te), were tested. These flow rates and temperatures are typical for industrial nozzle sizes with exit orifice sizes of 17 mm and 22 mm. An imaging method to measure droplet size in a highly challenging furnace environment was developed. Droplet volume median diameter (Dv50) for nozzles A, C, and T varied between 7 mm to 4 mm, 7 mm to 5 mm, and 8 mm to 6 mm, depending on the flow rate and temperature. The high number of droplets detected by the analysis program enabled data fitting into statistical correlations. The size and width parameters for the Rosin™]Rammer droplet size distribution function could be defined. The droplet size distribution was found to be surprisingly wide, probably because of swollen droplets. Spray velocity was measured in two locations, 5 cm from the nozzle and 1.8 m from the nozzle. Near the nozzle, the average velocity increased from 7.3 m/s to 13 m/s when the flow rate was increased from 2 L/s to 3 L/s. Increase of black liquor temperature increased spray velocity in most of the cases. At the distance of 1.8 m from the nozzle, average spray velocities varied between 4.0 m/s to 11 m/s, depending on nozzle geometry, flow rate, and temperature. The opening angles of the spray for nozzles A and C varied between 57™‹ to 78™‹. The opening angle of nozzle T with flow guide varied between 48™‹ to 56™‹. The highest penetration of the spray was estimated for nozzle T because of the narrow spray and large droplets.
Journal articles
Image classification of the furnace bed height in recovery boilers, TAPPI Journal July 2026
ABSTRACT: The goal of this study is to develop an approach for classifying char bed height in a recovery boiler during operation. The resulting classified images form a dataset that can be used by the mill to support operational improvements. The study integrates data from the digester, evaporation plant, recovery boiler, and recausticizing plant, along with the classified image data. A convolutional neural network (CNN) was trained on bed camera images that were manually annotated to classify furnace bed height. The model was then used to generate a binary bedheight parameter over a 16-month period, and an extreme gradient boosting (XGBoost) model was applied to identify relationships with operating parameters across the recovery cycle. The outcomes of this research may offer deeper insights into the processes underlying bed dynamics. Ultimately, the developed system may serve as a tool for optimizing bed conditions and supporting stable combustion.
Journal articles
Guest Editorial: Carrying forward the tradition of fundamental research, TAPPI Journal June 2026
Since its first symposium in 1957, the Fundamental Research Symposium has evolved around fundamental research themes aimed at scientifically understanding papermaking. The symposium is organized by the Fundamental Research Committee (FRC), which is operated by the Fundamental Research Society (FRS). The unique format of the symposium, held at universities such as Oxford and Cambridge where participants stay together, fosters intensive academic exchange and collegial interaction.
Journal articles
Editorial: Advancing the Digital Twin paradigm — From network mechanics to functional paper physics, TAPPI Journal March 2026
This Special Paper Physics Issue of TAPPI Journal serves as a critical bridge between the phenomenological observations shared at the last International Paper Physics Conference in Wuppertal, Germany, and the rigorous quantification required to realize the “Digital Twin” paradigm. This paradigm involves the creation of a virtual dynamic representation of a process that acts as a real-time counterpart of the actual one. We are particularly indebted to Jaan-Willem Simon of the University of Wuppertal, whose leadership was pivotal in translating the conference’s academic rigor into this scholarly collection.
Journal articles
Estimating dose and interaction of X-rays with cellulose-based fibrous materials using micro-computed tomography, TAPPI Journal March 2026
ABSTRACT: Micro-computed tomography (ìCT) has a reputation as a nondestructive analysis method. Unfortunately, this leads to the common misconception that radiation damage of the sample does not play a role. With the increased use of ìCT in laboratory-based machines, more and more cellulose-based materials are studied. In this paper, we show with three examples that radiation damage is important in dry and wet paper and in viscose fibers. In an attempt to quantify radiation damage, we came up with a workflow that enables researchers to predict the X-ray dose within a laboratory-based ìCT machine. This gives researchers the possibility to quantitatively judge the influence of radiation damage on each measured sample. While one cannot extend the measured doses from one machine to another, one can still apply the work flow presented in this study to any ìCT setup. In this way, it is possible to minimize radiation damage by choosing the best parameters in a ìCT for obtaining perfect data with no or little radiation damage.
Journal articles
Point load measurements on paperboard packages and bulging, TAPPI Journal March 2026
ABSTRACT: Paperboard packaging is made by processing board materials into sheets or rolls and shaping them through creasing, cutting, folding, and erecting. The conversion process generates residual moments at the folds that cause panel bulging. This study experimentally investigates how the bulging introduced during the converting processes influence the mechanical response of paperboard packages during point load testing within the elastic deformation range. The study shows that panel bulging may significantly affect packaging performance as-perceived strength and stiffness. Bulging, influenced by the board’s basis weight, can affect the package performance even more than packaging stiffness. Point load tests in the elastic region were performed on empty packages (78 mm × 50 mm × 110 mm) with force applied at specific points along their long sides. The packages evaluated in this study were made of two identically processed materials of different grammages. The heavier material showed more pronounced bulging than the lighter one, leading to overlapping force-displacement curves for the packages, and to that, a lower force and stiffness may be measured at a certain indentation depth for the package of heavier material. This complicates material choice according to functional requirements. The results show that a highly bulged package might resemble one with less bulging of another material. According to the results, it is not certain that a higher grammage package shows a higher indentation force and stiffness than a lower grammage package when measured at a certain indentation. This indicates that optimizing the creasing and folding processes can be a way to enhance performance rather than simply increasing board weight. The study underscores the importance of controlling converting parameters, especially creasing and folding behavior. Well-performed creasing and folding gives a low residual momentum, little bulging, and a high stiffness and compression strength at point loading in the elastic region. Proper optimization can improve packaging performance and manual handling user-friendliness.
Extrusion Equipment Overview, 1993 International European Extrusion Coating Symposium Proceedings
Extrusion Equipment Overview, 1993 International European Extrusion Coating Symposium Proceedings
Evaluating Alternative Processes for Plastics Film Production, 1993 International European Extrusion Coating Symposium Proceedings
Evaluating Alternative Processes for Plastics Film Production, 1993 International European Extrusion Coating Symposium Proceedings
Increased Productivity Via Innovative Die Design, 1993 International European Extrusion Coating Symposium Proceedings
Increased Productivity Via Innovative Die Design, 1993 International European Extrusion Coating Symposium Proceedings
Corona Treatment: An Overview, 1993 International European Extrusion Coating Symposium Proceedings
Corona Treatment: An Overview, 1993 International European Extrusion Coating Symposium Proceedings