Search
Use the search bar or filters below to find any TAPPI product or publication.
Filters
Content Type
Publications
Level of Knowledge
Committees
Event Type
Collections
Journal articles
Magazine articles
Evaluation of the particle size of organosolv lignin in the
Evaluation of the particle size of organosolv lignin in the synthesis of resol resins for plywood and their performance on fire spreading, TAPPI JOURNAL July 2017
Conference papers
Boosting the elongation potential of paper by mechanical refining and additives, 18PaperCon
Boosting the elongation potential of paper by mechanical refining and additives, 18PaperCon
Journal articles
Non-process elements in the lime cycle: New findings regarding NPE distribution and lime mud filterability, TAPPI Journal July 2026
ABSTRACT: Proper functioning of the recausticizing cycle is crucial for securing a stable white liquor supply for a pulp mill. Common runnability problems in the modern lime cycle, such as low filterability and poor dewatering of lime mud, high dead load, or ring formation in the lime kiln, are often caused by accumulation of non-process elements (NPEs). This project attempted to verify the traditional rules of thumb regarding the chemical behavior of NPEs: magnesium (Mg), aluminum (Al), silicon (Si), phosphorus (P), zinc (Zn), manganese (Mn), iron (Fe), copper (Cu), barium (Ba), cadmium (Cd), and lead (Pb) in the causticizing reaction, and to investigate the reasons behind poor lime mud filterability. First, a standardized method for measuring filterability of lime mud was developed. Next, a series of recausticizing experiments, followed by immediate filtration trials, was conducted using mill green liquors, laboratory-made synthetic green liquor, reburned lime/makeup mix, and extra NPE additions. It was found that sodium (Na), potassium (K), and sulfur (S) followed the liquid phase, as expected, while Mg, P, and Ba, but also Pb, Cu, and Cd, showed low solubility and accumulated in the lime mud. The Si and Al accumulated in the lime mud even though the soluble content in liquor was high, while the behavior of Mn, Fe, and Zn was more complex. Based on these results, tentative solubility limits for NPEs were suggested as a first estimate for the maximum possible concentrations of NPEs in mill white liquor. The causticization-filtration experiments revealed that overliming and high content of Mg in green liquor clearly led to lower filterability, but our addition of Si did not have such an effect. As differences in particle size and size distribution have a certain impact on the filtration resistance, the lime mud sedimentation behavior, combined with other characterization methods, might be used as an indication for the filterability. Finally, a list of recommendations for pulp mills was formulated that starts with establishing a comprehensive standard for a lime mud with good filterability. This standard can be used as a benchmark for comparison any time a lime cycle runnability problem is identified.
Journal articles
Exploratory study on how sub-ply fiber orientation affects t
ABSTRACT: The transition to 100% biobased packaging presents considerable challenges, particularly in the development of a petroleum-free barrier. Generally, biobased barriers exhibit lower flexibility compared to traditional barriers, thereby increasing the risk of cracking during the converting process. The present study examines the possibility of optimizing the substrate to reduce cracking in brittle barriers. Five three-ply composites were fabricated using commercial paperboard to enable a composite with different fiber orientation in the individual plies. The different orientations achieved varying mechanical properties, including strain-atbreak and folding resistance, with a ranking that is comparable to a standard multi-ply paperboard. The composites were subjected to creasing at five distinct depths to assess the area percent of barrier cracks across the crease bead. Micro-cracks appeared on the surface before larger coating cracks were registered. As expected, the area percent of barrier cracks increased significantly with greater creasing depths. The orientation of the bulky middle ply showed little difference in the cracking propensity. However, by replacing the stiffer bottom ply with a ply of lower stiffness, the cracking propensity was significantly reduced without a substantial loss in mechanical properties. Hence, these findings indicate that it is possible to reduce the cracks in the barrier by modifying the fiber orientation in the different plies.
Journal articles
Improving barrier performance of coated paper and paperboard
ABSTRACT: Market demand for barrier coated packaging paper and paperboard has been on a steady rise and is forecasted to further increase. As a result, there is a continued interest in improving barrier coating functionalities, which is currently an active area of investigation. In this work, a multi-layer approach was adopted that involved applying a biowax emulsion, latex, or a combination of biowax and latex top coating layer onto the kaolin/latex (20/80, 50/50, 65/35, or 70/30) precoated solid bleached sulfate (SBS) paperboard. Our main objective was to demonstrate the effect of these top coating layers on various barrier properties, especially water vapor transmission rate (WVTR) at high relative humidity (RH) and high temperature (90% RH; 38°C), known as tropical/jungle test conditions. While the top coat with latex and/or biowax showed dramatic improvement in both water resistance (Cobb) and WVTR, the biowax coating increased contact angle significantly compared to the latex top coat. Contact angle increased from about 65° for the latex top coat to as high as 96° for the biowax top coat. Generally, it is much more difficult to improve WVTR at the jungle conditions below 100 g/m2/day, even with the high aspect ratio platy pigment. However, using the coating strategies adopted in this study, we were able to achieve WVTR values notably below 50 g/m2/day at the tropical test conditions, as well as significant improvements in regard to fold crack barrier integrity at high kaolin clay usage.
Journal articles
Prediction of residual calcium carbonate (CaCO3) in the lime
ABSTRACT: In a kraft pulp mill, the rotary lime kiln is responsible for converting calcium carbonate (CaCO3) into calcium oxide (CaO) to be reused in the causticizing plant. An important parameter of the calcination efficiency and the product quality is the amount of CaCO3 not converted to CaO, commonly defined as residual carbonate. This parameter is usually determined through laboratory analysis, which introduces delays in process control and limits the ability to make timely operational adjustments. This work presents a predictive model that functions as a soft sensor for the residual carbonate in a lime kiln of a Brazilian kraft pulp mill. This model was able to estimate residual CaCO3 every 30 min using routinely measured online process variables, which is a considerable reduction from the 6-h average laboratory measurement. The correlation coefficient (r) between the model predictions and the mill values was 0.83, with a mean absolute error (MAE) of 0.33%. Considering the effect of the residence time throughout the lime kiln proved to be decisive in obtaining a satisfactory prediction result. After model validation, a variable importance analysis showed that the carbon monoxide (CO) concentration in the stack flue gas (in ppm), secondary air temperature (in oC), and fan speed (in %) were the most influential variables in predicting the residual carbonate content. Combined with commonly used operation expertise, this subset of variables can serve as additional information to achieve smoother lime kiln operation.
Literature Cited
Literature Cited As a general rule: In text and for literature cited, set titles in italics, capitalize only the first word of articles, but treat book titles as proper names. TAPPI JOURNAL Starting
TAPPI JOURNAL Author Guidelines
TAPPI JOURNAL Author Guidelines TAPPI JOURNAL Author Guidelines TAPPI JOURNAL is a peer-reviewed journal covering research on topics important to academics and professionals in the pulp, paper and
Effect of Pulp Delignification Degree and Bleaching Process on an Eucalyptus Fiber Line Performance and Economic, 2007 Engineering, Pulping & Environmental Conference
Effect of Pulp Delignification Degree and Bleaching Process on an Eucalyptus Fiber Line Performance and Economic, 2007 Engineering, Pulping & Environmental Conference
News
Steven Keller
See the goal for Miami University Professor, and recently inducted TAPPI Fellow, Steven Keller, Ph.D.