Search
Use the search bar or filters below to find any TAPPI product or publication.
Filters
Content Type
Publications
Level of Knowledge
Committees
Event Type
Collections
Journal articles
Comparison of the application of polysaccharide-based barrier coatings on paper using film press and spray coating, TAPPI Journal January 2025
The growing demand for sustainable packaging has spurred research into biopolymer-based solutions and their application to paper substrates. This study compares the application of low solids, high viscous aqueous solutions of alginate and chitosan on two different paper substrates using a laboratory film press coater and a purpose-built spray coating unit, with a focus on barrier performance and practical industry considerations. Key parameters investigated are air flow rate, water vapor transmission rate, and grease resistance. Results showed that due to the low solids content of the applied biopolymer solutions, film press coating required a double-layer application for coat weights exceeding 4 g/m², making it less viable for industrial application. In contrast, spray coating allowed for higher application weights in a single step. The barrier properties of spray coated samples, compared to film press coatings, varied with the paper substrate: spray coating performed better on one substrate and worse on the other. Contact angle measurement of the substrates suggested that spray coating is more suitable for a more hydrophilic substrate because of improved surface wetting. The study also identified issues with drying conditions and pinholes affecting the quality of spray coated samples, indicating a need for further research to optimize these parameters.
Journal articles
Water-based adhesive penetration into paperboard and coated paperboard, TAPPI Journal January 2025
The setting of water-based adhesives in contact with paperboard is important in the production of boxes and other packaging, but the topic has received little attention in the literature. The penetration of the adhesive into the paper surface is important to get good bond strength through mechanical interlocking. The influence of the process conditions and the paper properties on this penetration is lacking. A water-based adhesive was applied to an uncoated and coated paperboard. The coating layer had two latex levels. Samples were characterized in terms of air permeability, void fraction, average pore size, and coat weight. The adhesive was applied to the samples in a mechanical press, squeezing a drop between two samples. The penetration of the adhesive was characterized with a silicone oil absorption method that measured the decrease in pore volume after the adhesive had been applied to approximate the pore volume taken up by the adhesive. The bond strength was measured with a peeling test. The penetration depth into uncoated paper did not depend on the application method parameters such as pressing time, pressure, or initial solids of the adhesive. The penetration depth ranged from 35•40 mm. The penetration into 10 pph latex content coated paper was similar to the uncoated samples, but reduced penetration was observed into the 40 pph latex content coatings. The results were compared to the limiting amount of adhesive that was obtained from the weight gain of the samples and to a simple model that is based on flow in porous media. Peel tests revealed that good penetration was needed, as well as a strong coating layer to obtain high peel forces.
Journal articles
Reducing aox by increasing oxidation potential in the first caustic extraction stage, TAPPI Journal December 2024
Authors: Peter W. Hart and Jeffrey S. Hsieh | Tappi J. 74(11): 117(1991) - ABSTRACT: An increase in the standard oxidation potential of the reinforcing agent in the first caustic extraction stage will reduce the amount of AOX in the stage's effluent. A chlorinated broumstock pulp was treated alternatively in a basic caustic extraction (E) stage, an oxygen-reinforced caustic extraction (EO) stage, and an extraction stage reinforced with oxygen and peroxide (EOP). An AOX reduction of up to 30% was obtained in the effluent from the peroxide-reinforced extraction stage. In addition to the brownstock work, using two different model lignin compounds, we ran tests using oxyen, potassium permanganate, hydrogen peroxide with oxygen, and ozone with oxygen-reinforced caustic stages. In all cases, increasing the oxidation potential of the reinforcing agent decreased the amount of AOX detected in the effluent.
Journal articles
Production of high yield bleached hardwood kraft pulp: Breaking the kraft pulp yield barrier,TAPPI Journal December 2024
Author: Peter W. Hart | TAPPI J. 10(9): 37(2011) - ABSTRACT: A modified kraft pulping process has been developed that successfully breaks the traditional hard-wood kraft pulp yield barrier. The process produces fully bleached, high brightness hardwood kraft pulp with a yield of greater than 53% on wood. Details of the development and processing steps, along with various recovery cycle impacts, are discussed.
Journal articles
Hydrogen peroxide and caustic soda: Dancing with a dragon while bleaching,TAPPI Journal December 2024
Peter W. Hart, Carl Houtman, and Kilby Hirth | TAPPI J. 12(7): 59(2013) - ABSTRACT: When hydrogen peroxide is mixed with caustic soda, an auto-accelerating reaction can lead to generation of significant amounts of heat and oxygen. On the basis of experiments using typical pulp mill process concentration and temperatures, a relatively simple kinetic model has been developed. Evaluation of these model results reveals that hydrogen peroxide-caustic soda systems are extremely sensitive to hydrogen peroxide:caustic soda ratio, transition metal contamination, and temperature. Small changes in initial conditions can result in a closed system becoming explosive. Analysis of model results was used to develop guidelines for safer application of hydrogen peroxide in a mill setting.
Journal articles
Magazine articles
Comparing a linear transfer function-noise model and a neural network to model boiler bank fouling in a kraft recovery boiler, TAPPI Journal, July 2024
ABSTRACT: Boiler bank fouling reduces heat transfer efficiency in kraft recovery boilers. Here, we model the relationships between boiler parameters and boiler bank pressure drop, an indicator of fouling, based on recovery boiler operating data. We compared two models: an autoregressive integrated exogenous (ARIX) model and a feedforward neural network. The ARIX model better simulates boiler bank pressure drop compared to the neural network (R2 of 0.64 vs. 0.58). Based on the ARIX model, we identified six boiler parameters that significantly influence boiler bank fouling and their relative contributions. Finally, we demonstrate how the models can simulate boiler bank pressure drop given artificial perturbations in boiler parameters.
Journal articles
Magazine articles
Effects of different soda loss measurement techniques on brownstock quality, TAPPI Journal July 2024
ABSTRACT: The efficiency of the kraft recovery plant, bleaching process, and paper machine are affected when black liquor carryover from the brownstock washers is not controlled well. Measuring soda loss within a mill can vary from using conductivity, either in-situ or with a lab sample of black liquor filtrate squeezed from the last stage washer, to measuring absolute sodium content with a lab sodium specific ion probe or spectrophotometer. While measuring conductivity has value in tracking trends in black liquor losses, it is not an acceptable method in reporting losses in absolute units, typically in lb/ton of pulp. This is further complicated when trying to benchmark soda loss performance across a fleet of mills with multiple washer lines. Not only do the testing methods vary, but the amount of bound soda on high kappa pulps can be significant. This variability creates inconsistent results, and studies are needed to understand the effect of different testing methods on the pulp quality. In this study, soda loss is expressed as sodium sulfate (Na2SO4). Four different methods to measure soda content in pulp off commercial brownstock washers were studied: full digestion (FD), washing soaking overnight and washing (WSW), soaking in boiling water and stirring 10-min (SW-10), and squeeze-no wash (Sq). Total, washable, and bound sodium sulfate calculations were determined for each soda content measuring technique using inductively coupled plasma-optical emission spectroscopy (ICP-OES). Results showed bound and washable sodium sulfate amounts significantly depend on which soda measurement technique was used. In addition, the soda results were correlated with the pulp kappa numbers. As the kappa number increases, bound soda increases, regardless of the soda measurement method used. Impacts of high sodium sulfate in brownstock are also discussed.
Journal articles
Magazine articles
A new and quick testing method for evaluating commercial OCC recycled pulp, TAPPI Journal July 2024
ABSTRACT: In this paper, a new and quick testing method for evaluating commercial old corrugated cardboard/containers (OCC) pulp was developed and used by a large Chinese boxboard manufacturer for quality control of imported OCC pulp.
Journal articles
Magazine articles
Editorial: Special pulping and engineering issues of TAPPI Journal yield important recovery cycle research, TAPPI Journal June 2024
ABSTRACT: The June issue of TAPPI Journal, which is dominated by recovery cycle topics, is the last PEERS issue organized by Dr. Peter Hart, the fomer editor-in-chief who passed away this past May. Peter, who was heavily involved with TAPPI’s Pulp Manufacture Division and various pulping-related committees, also started working with conference technical program planning starting in 2005 with the Engineering, Pulping and Environmental (EPE) Conference, which was the precursor to the more recent Pulping, Engineering, Environmental, Recycling and Sustainability (PEERS) Conference. He was also involved with other conference planning, including that for the International Pulp Bleaching Conference. In addition, Peter was a yearly attendee of such conferences starting as far back as 1990.
Kraft pulp viscosity as a predictor of paper strength: Its uses and abuses, TAPPI Journal October 2023
ABSTRACT: For bleached kraft pulps, two factors govern paper strength: the individual fiber strength, and the bond strength that adheres the individual fibers together in the paper matrix. Inherent fiber strength is related to the length of the carbohydrate polymers, also known as the degree of polymerization (DP). Average DP (DP) is inferred by performing pulp viscosity measurements. Under certain circumstances during kraft pulping and bleaching, the average polymer lengths can be shortened, resulting in lower pulp viscosity, and may indicate fiber damage. Fiber damage typically manifests itself as a reduction in tear strength for well-bonded handsheets.This paper will review the literature on how pulp viscosity can predict paper/fiber strength and how it can be used as a diagnostic tool. It can be a means to monitor pulp quality during pulping and bleaching, as well as to alert when such operations approach a critical threshold. However, viscosity losses must be carefully and judiciously analyzed. Like most diagnostic tools, viscosity measurements can be misused and abused, which can lead to incorrect inferences about intrinsic fiber strength. This review will also cover these misuses. The overall goal is to provide the papermaker a better understanding of what pulp viscosity is, how it correlates to potential sheet strength, and what its limitations are. It will be illustrated that when pulp viscosity drops below a critical value, it will indicate an appreciable deterioration in the paper’s tear and tensile strength.