Search
Use the search bar or filters below to find any TAPPI product or publication.
Filters
Content Type
Publications
Level of Knowledge
Committees
Collections
Journal articles
Magazine articles
Evaluation of novel drum chipper technology: pilot-scale production of short wood chips, TAPPI Journal October 2019
ABSTRACT: Impregnation of wood chips with acidic pulping liquors is improved when using short chip lengths. If the average wood chip length is too short, conventional chipping technology will generate excess small material, such as pin chips and fines. The possibility of using newly developed drum chipping technology to produce short-length wood chips was evaluated with a pilot drum chipper operating at different drum velocities and in-feed angles. With a drum velocity of 30 m/s, the average wood chip lengths and the combined fractions of pin chips and fines were 24 mm and 3.3%, 22 mm and 4.2%, and 17 mm and 8.5%. The highest fractions of total accept chips (large and small accepts), 89% to 90% without screening, were observed for drum velocities of 30•34 m/s and average wood chips lengths of 21•22 mm. The results indicate the potential of drum chipping technology for producing short wood chips with relatively high fractions of accept chips and tolerable fractions of pin chips and fines.
Journal articles
Magazine articles
Editorial: New coating grades require new tests: Barrier performance inside the package, TAPPI Journal November 2024
The TAPPI Journal special Coating issue is an annual issue that focuses on paper coating and coated papers. It is drawn from presentations at TAPPICon and from other submissions on the topic of paper coating. The TAPPICon 2024 Coating track was rich in high-quality technical content. In fact, the papers were of such significance that Coating members of the TAPPI Journal Editorial Board, which include me, Gregg Reed, and Gregory Welsch, decided that a second paper coating-related special issue would be appropriate for the TAPPI Journal editorial calendar. In addition to the current issue on Barrier Coating Testing, there will be another issue on Coating Fundamentals in early 2025.
Journal articles
Magazine articles
Test method and coating composition impact on measured moisture vapor transmission rate for waterborne coatings on paper, TAPPI Journal November 2024
ABSTRACT: Moisture vapor barrier is one of the necessary performance attributes for paper packages. Two methods are typically employed to assess the moisture vapor transmission rate (MVTR): the gravimetric cup method (ASTM E96) and the MOCON method (ASTM F1249). While those tests have been compared for free standing polymeric films, less is understood about their application in coated paper. Our results show that, despite a general agreement between the two methods, discrepancies exist where test protocols and material properties of coated paper impact the MVTR measurement. The measurement discrepancies can be explained by differences in local moisture concentration. Our study provides new insights on moisture vapor barrier assessment of waterborne coatings on paper and implications for achieving paper packages with improved barrier performance.
Journal articles
Filtration performance of face masks and facepiece respirators used during COVID-19 pandemic, TAPPI Journal February 2025
ABSTRACT: The rapid spread of SARS-CoV-2 has created challenges for societies, healthcare settings, businesses, and institutions. To curb virus transmission, various measures like lockdown, social distancing, hand hygiene, and using appropriate personal protective equipment (PPEs), including face masks, have been recommended. Face masks and facepiece respirators are considered to act as barriers against microbial transmission from person to person. In this study, we selected barrier materials used during the COVID-19 pandemic that included four non-medical face masks and three facepiece respirators. Facepiece respirators were distributed by the U.S. Administration through pharmacy outlets. Results showed that facepiece respirator R95 has the highest filtration efficiency (above 99%), which remains more or less the same over different particle sizes. The N95 respirator’s filtration efficiency was lower than that of R95, but its barrier resistance was lower than that of the R95, indicating that it can be comfortably used over longer duration. Face masks were evaluated using ASTM F 3502-24 for their barrier performance. At 0.1 and 0.3 ìm particle size, domestically manufactured masks met the standard for higher performance. Interestingly, the results indicate that quality of raw materials and manufacturing standards play important roles, as is evident in domestically manufactured face mask and facepiece respirators.
Journal articles
Magazine articles
Development of converging-diverging multi-jet nozzles for molten smelt shattering in kraft recovery boilers, TAPPI Journal March 2021
ABSTRACT: The effective shattering of molten smelt is highly desired in recovery boiler systems. Ideally, shatter jet nozzle designs should: i) generate high shattering energy; ii) create a wide coverage; and iii) minimize steam consumption. This study proposes a novel converging-diverging multi-jet nozzle design to achieve these goals. A laboratory setup was established, and the nozzle performance was evaluated by generating jet pressure profiles from the measurement of a pitot tube array. The results show that the shatter jet strength is greater with a large throat diameter, high inlet pressure, and a short distance between the nozzle exit and impingement position. Increasing the number of orifices generates a wider jet coverage, and the distance between the orifices should be limited to avoid the formation of a low-pressure region between the orifices. The study also demonstrates that an optimized converging-diverging multi-jet nozzle significantly outperformed a conventional shatter jet nozzle by achieving higher energy and wider coverage while consuming less steam.
Journal articles
Magazine articles
Quantification of vegetable oil in recycled paper, TAPPI JOURNAL September 2020
ABSTRACT: Vegetable soybean oil is commonly used in cooking foods that are packaged in takeaway paper-board containers. Vegetable oil is hydrophobic, and in sufficiently high concentration, could interfere with interfiber bonding and result in paper strength loss. In order to quantify the effect of oil on the resulting paperboard strength, it is necessary to quantify the oil content in paper. A lab method was evaluated to determine the soybean oil content in paper. Handsheets were made with pulps previously treated with different proportions of vegetable oil. Pyrolysis gas chromatography-mass spectrometry (pyGCMS) was used to quantify the amount of oil left in the handsheets. The results revealed a strong correlation between the amount of oil applied to the initial pulp and the amount of oil left in the handsheets.In addition, the effect of vegetable oils on paper strength may be affected by the cooking process. Vegetable oil is known to degrade over time in the presence of oxygen, light, and temperature. The vegetable oil was put in an oven to imitate the oil lifecycle during a typical pizza cooking process. The cooked oil was then left at room temperature and not protected from air (oxygen) or from normal daylight. The heated, then cooled, oil was stored over a period of 13 weeks. During this time, samples of the aged oil were tested as part of a time-based degradation study of the cooked and cooled oil.
Journal articles
Magazine articles
Recycling performance of softwood and hardwood unbleached kraft pulps for packaging papers, TAPPI Journal February 2023
ABSTRACT: The scope of this work is to evaluate the recyclability potential of hardwood and softwood unbleached kraft pulps, leading to a sound basis for comparison and even to support a decision about fibers accord-ing to the performance achieved. The influence of successive recycling cycles (up to 10 cycles) on the fiber morphol-ogy, pulp suspension drainability, water retention capacity, and handsheet mechanical properties were studied for Eucalyptus globulus and Pinus sylvestris unbleached kraft pulps. The performance of these pulps as linerboard and corrugating medium for packaging was also evaluated. The requirements for brown kraftliner and for high perfor-mance recycled fluting grades is preserved for E. globulus pulp during all 10 recycling cycles, evidenced by the mod-erate decrease of burst index and crush resistance index and by the short-span compression index, whereas the P. sylvestris pulp loses this rating after the second cycle. These results strongly support the higher performance of E. globulus pulp for recycling as compared with softwood kraft pulp from the perspective of packaging papers.
Journal articles
Magazine articles
Chemical addition to wet webs using foam application, TAPPI Journal January 2023
ABSTRACT: In papermaking, the conventional way to add chemicals to the web is to dose them into the fiber stock and form the paper afterwards. However, in many cases, adding chemicals directly to the stock is challenging. For example, strength aids tend to increase flocculation in the stock, which limits the addition amounts of those aids. The need for better performance of paper (and paperboard) products has given rise to the need for functionalization of paper. Adding such functional chemicals to the stock is usually rather inefficient. Hence, novel methods are needed to add chemicals to the paper bulk. One such method is dosing chemicals to the wet web via foam application. In this study, we built a laboratory-scale sheetfed dynamic foam application device and utilized it to study addition of starch to wet bleached chemithermomechanical pulp (BCTMP) paper handsheets. The impact of parameters such as vacuum level, the amount of added chemical, and the viscosity of the foaming liquid on the penetration of starch into the wet web was explored. Starch penetration into wet webs was measured via iodine-potassium iodide staining, followed by image analysis. According to our results, controlling the viscosity of the foaming liquid gives the best possibility to control the penetration.
Journal articles
Magazine articles
Nanocellulose•cationic starch• colloidal silica systems for papermaking: Effects on process and paper properties, TAPPI Journal October 2022
ABSTRACT: Laboratory tests were conducted to better understand effects on the papermaking process and handsheets when recycled copy paper furnish was treated with combinations of nanofibrillated cellulose (NFC), cationic starch, colloidal silica, and cationic retention aid (cPAM; cationic polyacrylamide). Dosage-response experiments helped to define conditions leading to favorable processing outcomes, including dewatering rates and the efficiency of fine-particle retention during papermaking. Effects were found to depend on the addition amounts of cationic starch and colloidal silica added to the system. It was shown that the presence of a polymer additive such as cationic starch was essential in order to achieve large strength gains with simultaneous usage of NFC.
Journal articles
Magazine articles
Effects of different ammonium lignosulfonate contents on the crystallization, rheological behaviors, and thermal and mechanical properties of ethylene propylene diene monomer/polypropylene/ammonium lignosulfonate composites, TAPPI Journal January 2020
ABSTRACT: Thermoplastic elastomer (TPE), made from ethylene propylene diene monomer (EPDM) and polypropylene (PP) based on reactive blending, has an excellent processing performance and characteristics and a wide range of applications. However, there are currently no reports in the literature regarding the usage of TPE in making composite boards. In this paper, EPDM, PP, and ammonium lignosulfonate (AL) were used as the raw materials, polyethylene wax was used as the plasticizer, and a dicumyl peroxide vulcanization system with dynamic vulcanization was used to make a new kind of composite material. This research studied the influences of the AL contents on the crystallization behaviors, rheological properties, thermal properties, and mechanical properties of the composites. The results showed that the AL content had a noticeable impact on the performance of the composite board. Accordingly, this kind of composite material can be used as an elastomer material for the core layer of laminated flooring.