Search
Use the search bar or filters below to find any TAPPI product or publication.
Filters
Content Type
Publications
Level of Knowledge
Committees
Collections
Journal articles
Magazine articles
Root cause analysis of cationic polymer additive efficiency decline in virgin and recycle containerboard mills, TAPPI Journal January 2020
ABSTRACT: It is well known that retention, drainage and strength polymers struggle to perform (if at all) in virgin containerboard mills. In-depth studies have been undertaken in this area for more than seven years, investigating the issue from all directions. A key finding of this work is that soluble lignin is detrimental to chemical efficiency. A strong correlation exists between decreased chemical efficiency and high soluble lignin. Both recycled systems and virgin systems have been studied, and this correlation holds true regardless of furnish. The primary area of concern is virgin container-board, because these mills tend to have the highest lignin levels. Some highly closed recycled mills can also build elevated lignin levels that can negatively affect chemical efficiency.
Journal articles
Magazine articles
Combatting lime kiln ringing problems at the Arauco Constitución mill, TAPPI Journal July 2020
ABSTRACT: The lime kiln at the Arauco Constitución mill experienced severe ringing problems requiring it to be shut down for ring removal every 3 to 6 months. The mill controlled the problems by blasting ring deposits off during operation with its existing industrial shotgun and a newly installed Cardox liquid carbon dioxide (CO2) cartridge system. Various ring blasting procedures were tested to determine the optimum ring location and thickness to blast; the optimum depth to insert the CO2 cartridge into the kiln; and the most effective blasting frequency and sequence to employ. The best strategy was found to be the weekly blasting operation that alternated between the liquid CO2 cartridge and the industrial shotgun, with the CO2 cartridge inserted into the ring mass, 20 cm (8 in.) away from the refractory brick surface, and the shotgun aimed at rings at about 28 m (92 ft) from the kiln discharge end. With each blasting event removing considerably more rings than before, it takes a longer time for rings to rebuild, allowing the kiln to run continuously between annual maintenance shutdowns with only a few short (< 4 h) downtimes for ring removal. This substantially reduces the costs associated with ring removal and lime replacement during unscheduled shutdowns.
Journal articles
A method to produce paperboard with a lightweight low-density coating, TAPPI Journal November 2025
ABSTRACT: In this work, a method is described in which a coating layer is produced that consists of a network of bubble-shaped air-filled voids within the coating. This is accomplished by instantaneously flash-drying all the water in the coating as it exits the application nip. The nip is formed between a polished chrome drum and a deformable press roll. The combination of the drum temperature, nip pressure, and nip width allow for sufficient energy to be transferred to the coating to completely flash-dry the coating material. The pressure within the nip is sufficient to allow the coating to superheat within the nip, then flash boil as it exits the nip. This boiling effect and resulting expansion are constrained by the roll surface, resulting in a coated surface that mirrors the polished chrome surface. The coating immobilizes while in the process of boiling, which preserves the bubble structure. With a coat weight of 5 g/m2, a flat, smooth surface is produced. This process was scaled up to a mill production machine layout and run at speeds as high as 450 m/min.
Journal articles
Effect of pulp refining on thixotropy of cellulose fiber suspensions, TAPPI Journal September 2025
ABSTRACT: This paper presents results on the thixotropic behavior of low-consistency bleached eucalyptus fiber suspensions that had been mechanically treated. The pulps were refined in a PFI mill at different numbers of revolutions (0, 3000, and 6000) to study the effect of refining intensity on the viscosity time-response of fiber suspensions. In steady rheological tests, all the suspensions exhibited shear thinning behavior and no significant differences were observed after mechanical treatment. Stepwise experiments showed that viscosity continuously increased with time when shear rate was suddenly reduced. Additionally, a delay in time evolution of viscosity was observed as the pulp was more refined. A stretched exponential model was fitted to the experimental results of viscosity.
Journal articles
Estimating dose and interaction of X-rays with cellulose-based fibrous materials using micro-computed tomography, TAPPI Journal March 2026
ABSTRACT: Micro-computed tomography (ìCT) has a reputation as a nondestructive analysis method. Unfortunately, this leads to the common misconception that radiation damage of the sample does not play a role. With the increased use of ìCT in laboratory-based machines, more and more cellulose-based materials are studied. In this paper, we show with three examples that radiation damage is important in dry and wet paper and in viscose fibers. In an attempt to quantify radiation damage, we came up with a workflow that enables researchers to predict the X-ray dose within a laboratory-based ìCT machine. This gives researchers the possibility to quantitatively judge the influence of radiation damage on each measured sample. While one cannot extend the measured doses from one machine to another, one can still apply the work flow presented in this study to any ìCT setup. In this way, it is possible to minimize radiation damage by choosing the best parameters in a ìCT for obtaining perfect data with no or little radiation damage.
Journal articles
Magazine articles
Mechanistic aspects of nanocellulose•cationic starch•colloidal silica systems for papermaking, TAPPI Journal February 2023
ABSTRACT: Optimization of a chemical additive program for a paper machine can require attention to both colloidal charges and kinetic effects. This work considered an additive program with two negatively charged substances (nanofibrillated cellulose [NFC] and colloidal silica) and two positively charged items (cationic starch and cationic acrylamide copolymer retention aid). Results were shown to depend on charge interactions; however, that clearly was not the whole story. Some findings related to cationic demand, dewatering, fine-particle retention, and flocculation among fibers were best explained in terms of at least partly irreversible complexation interactions between the charged entities. Adjustments in ratios between oppositely charged additives, their sequences of addition, and effects of hydrodynamic shear levels all affected the results. In general, the most promising results were obtained at a cationic starch level of 0.25% to 0.5% based on sheet solids in systems where the cationic starch was used as a pretreatment for NFC.
Journal articles
Magazine articles
An analytical method to quantitatively determine the amount of polyamide epichlorohydrin (PAE) in paperboard and white water, TAPPI Journal February 2023,
ABSTRACT: Polyamide epichlorohydrin (PAE) is a permanent wet strength resin. When applied to paperboard, some amount of resin is retained in the sheet, and some is lost to the white water. An analytical method for quantifying the amount of PAE retained in the sheet and lost into the white water has been developed. This method hydrolyzes the PAE to adipic acid, which in turn is derivatized to diethyl adipate and quantified by pyrolysis gas chromatography•mass spectrometry (pyGCMS). In addition, the hydrolysis conditions of the PAE were studied by the Taguchi approach, and PAE material balances around the dry sheet and white water for 3 and 6 lb/ton PAE applications have been performed. The PAE resin recovery was 95.4% with 65.0% in the sheet for the 3 lb/ton PAE-charged paper-board, and the recovery was 96.7% with 36.1% in the sheet for the 6 lb/ton PAE-charged paperboard.
Journal articles
Magazine articles
New opportunities in the paper and nonwovens industries with foam-assisted web forming and chemical application, TAPPI Journal January 2023
ABSTRACT: Foam-assisted web forming and chemical application technologies have great potential to improve manufacturing efficiency and product quality in the paper and nonwovens industries. In this study, the benefits of foam forming and foam-assisted application of chemicals were demonstrated in a pilot machine trial. Uniform high-bulk webs of unrefined bleached softwood kraft pulp (BSKP) and viscose fibers were manufactured by foam forming. It was shown that foam formed low-grammage and high-bulk viscose fiber webs can be strengthened by foam-assisted application of latex onto the wet web. Correspondingly, foam-assisted application of carboxymethyl cellulose (CMC) and anionic polyacrylamide (A-PAM) improved the strength of the foam formed low-grammage and high-bulk BSKP web. Overall, the pilot machine results indicated that material cost savings could be achieved and a high-performance product could be manufactured with foam-based technologies.
Journal articles
Magazine articles
A discrete element method to model coating layer mechanical properties with bimodal and pseudo-full particle size distributions, TAPPI Journal July 2023
ABSTRACT: The mechanical properties of paper coating layers are important in converting operations such as calendering, printing, and folding. While several experimental and theoretical studies have advanced our knowledge of these systems, a particle level understanding of issues like crack-at-the-fold are lacking.A discrete element method (DEM) model is used to describe bending and tension deformations of a coating layer. The particles in the model are either bimodal distributions or pseudo-full particle size distributions of spherical particles. The impact of particle size distribution on the predicted mechanical properties of the coating layer is reported. Inputs to the model include properties of the binder film and the binder concentration. The model predicts crack formation as a function of these parameters and also calculates the modulus, the maximum stress, and the strain-to-failure. The simulation results are compared to previous experimental results. Reasonable predictions were obtained for both tensile and bending for a range of latex-starch ratios and at various binder concentrations. The influence of particle packing density on mechanical properties is reported.
Journal articles
Magazine articles
External fibrillation of wood pulp, TAPPI Journal June 2023
ABSTRACT: Pulp refining produces external fibrillation consisting of fibrils tethered to fiber surfaces, in addition to loose fibrils and fines. Both contribute to a larger bonding area that increases paper strength, but tethered fibrils have less likelihood of being washed out during papermaking. This study postulates the mechanism by which refining produces external fibrillation and the optimum conditions for doing so.The postulated mechanism is surface abrasion during sliding of fibers in refiner gaps. External fibrillation occurs when forces are great enough to partially dislodge fibrils from fiber surfaces, but not large enough to break the fibrils. The refining intensities to achieve these forces were determined by a mathematical model and experiments using a laboratory disc refiner. The optimum intensities in terms of specific edge load (SEL) for chemical pulps were about 0.1 J/m for hardwoods and 1.0 J/m for softwoods. An extension of this study suggested that abrasion may also account for most of the energy consumed in the mechanical pulping process.