Search
Use the search bar or filters below to find any TAPPI product or publication.
Journal articles
Magazine articles
Characterization of chia plant (Salvia hispanica) for pulping, TAPPI Journal October 2020
ABSTRACT: In this paper, chia plant was characterized in terms of chemical, morphological, and anatomical properties. Chia plant was characterized with low a-cellulose (30.5%); moderate lignin (23.2%) with syringyl to guaiacyl ratio of 1.41; and shorter fiber length (0.67 mm) with thinner cell wall (1.91 µm) and good flexibility coefficient (71.44). Anatomical features showed that chia plant consists of vessels, fibers, parenchyma cells, and collenchyma cells. Chia plant pulping was evaluated in soda-anthraquinone (soda-AQ) and formic acid/peroxyformic acid (FA/PFA) processes. Chia plant was difficult to delignify in the alkaline process. The FA/PFA process produced higher pulp yield at the same kappa number than the soda-AQ process. Unbleached soda-AQ chia pulp exhibited good properties in terms of tensile, bursting, and tearing strengths, even at the unrefined stage, due to high drainability of the pulps. Alkaline peroxide bleached FA/PFA pulp exhibited better papermaking properties and 2% higher brightness than the D0(EP)D1 bleached soda-AQ pulp.
Journal articles
Magazine articles
Evaluation of novel drum chipper technology: pilot-scale production of short wood chips, TAPPI Journal October 2019
ABSTRACT: Impregnation of wood chips with acidic pulping liquors is improved when using short chip lengths. If the average wood chip length is too short, conventional chipping technology will generate excess small material, such as pin chips and fines. The possibility of using newly developed drum chipping technology to produce short-length wood chips was evaluated with a pilot drum chipper operating at different drum velocities and in-feed angles. With a drum velocity of 30 m/s, the average wood chip lengths and the combined fractions of pin chips and fines were 24 mm and 3.3%, 22 mm and 4.2%, and 17 mm and 8.5%. The highest fractions of total accept chips (large and small accepts), 89% to 90% without screening, were observed for drum velocities of 30•34 m/s and average wood chips lengths of 21•22 mm. The results indicate the potential of drum chipping technology for producing short wood chips with relatively high fractions of accept chips and tolerable fractions of pin chips and fines.
Journal articles
Magazine articles
Enzymatic treated viscose fibers functionalized by chitosan, TAPPI JOURNAL August 2018
Enzymatic treated viscose fibers functionalized by chitosan, TAPPI JOURNAL August 2018
Journal articles
Magazine articles
Effects of different ammonium lignosulfonate contents on the crystallization, rheological behaviors, and thermal and mechanical properties of ethylene propylene diene monomer/polypropylene/ammonium lignosulfonate composites, TAPPI Journal January 2020
ABSTRACT: Thermoplastic elastomer (TPE), made from ethylene propylene diene monomer (EPDM) and polypropylene (PP) based on reactive blending, has an excellent processing performance and characteristics and a wide range of applications. However, there are currently no reports in the literature regarding the usage of TPE in making composite boards. In this paper, EPDM, PP, and ammonium lignosulfonate (AL) were used as the raw materials, polyethylene wax was used as the plasticizer, and a dicumyl peroxide vulcanization system with dynamic vulcanization was used to make a new kind of composite material. This research studied the influences of the AL contents on the crystallization behaviors, rheological properties, thermal properties, and mechanical properties of the composites. The results showed that the AL content had a noticeable impact on the performance of the composite board. Accordingly, this kind of composite material can be used as an elastomer material for the core layer of laminated flooring.
Journal articles
Magazine articles
Techno-economic analysis of ECF bleaching and TCF bleaching
Techno-economic analysis of ECF bleaching and TCF bleaching for a bleached eucalyptus kraft pulp mill, TAPPI JOURNAL October 2017
Journal articles
Magazine articles
Tetraethyl orthosilicate-containing dispersion coating — water vapor and liquid water barrier properties, TAPPI Journal September 2021
ABSTRACT: An aqueous styrene-butadiene latex dispersion coating containing in-situ processed tetraethyl orthosilicate (TEOS) applied on paperboard demonstrated improved water barrier performance. Coatings containing TEOS equivalent to 0.8% silicon dioxide (SiO2; dry basis) exhibited water vapor performance of < 25 g/m2/day (23°C, 50% relative humidity [RH]) and liquid water barrier performance Cobb 1800 s of < 6 g/m2, when applied as a single-layer 18 g/m2 coating. Cobb 1800 s barrier performance was still good (< 11 g/m2) at coat weights of 7–10 g/m2. The use of filler materials such as kaolin improved the vapor barrier properties of the coating, but this was not critical to the liquid water barrier properties.
Journal articles
Magazine articles
Soybean peroxidase treatment of ultra-high kappa softwood pulp to enhance yield and physical properties, TAPPI Journal September 2020
ABSTRACT: The working hypothesis serving as basis for this study is that pulping to a higher kappa number will produce a higher yield pulp, and then treating that pulp with a surface reactive lignin peroxidase to ablate surface lignin will increase specific bonding area. In the present case, the working hypothesis was modified so that soybean peroxidase (SBP) works like lignin peroxidase to modify surface lignin on high-kappa, high-yield softwood pulps to facilitate enhanced fiber-to-fiber bonding such that the resulting paper strength is similar to the lower kappa soft-wood pulp generally used to make linerboard. Soybean peroxidase is actually a plant peroxidase that exhibits lignin peroxidase-like activity. It is not a lignin peroxidase derived from white rot fungus. The current work did show a significant improvement in pulp yield (62.2% vs. 55.2% yield for a 103-kappa control linerboard grade sheet), while treatment with SBP showed that tensile, burst, and STFI properties of the pulp were improved, although more convincing data needs to be obtained.
Journal articles
Magazine articles
Dissolution of wood components during hot water extraction of spruce, TAPPI Journal May 2023
ABSTRACT: The purpose of this study was to investigate the autohydrolysis of softwood, which is the main chemical operation in both hot water extraction and steam explosion. Control of the process and monitoring its course were ensured by the careful choice of experimental setup and conditions: a milled spruce material was extracted in a small flow-through reactor to minimize degradation of the dissolved material and to enable analysis of the resulting liquors extracted at selected time points. The obtained liquid and solid fractions were analyzed for sugar composition and acetic acid concentration. The results showed that partially degraded hemicelluloses were extracted; hemicelluloses side chains were cleaved off and detected as monomers, while deacetylation was limited. Chain scissions of cellulose were observed as a result of autohydrolysis.
Journal articles
Magazine articles
Critical parameters for tall oil separation I: The importance of ration of fatty acids to rosin acids, TAPPI Journal September 2019
ABSTRACT: Tall oil is a valuable byproduct in chemical pulping of wood, and its fractions have a large spectrum of applications as chemical precursors, detergents, and fuel. High recovery of tall oil is important for the economic and environmental profile of chemical pulp mills. The purpose of this study was to investigate critical parameters of tall oil separation from black liquor. To investigate this in a controlled way, we developed a model test system using a “synthetic” black liquor (active cooking chemicals OH- and HS- ions), a complete process for soap skimming, and determination of recovered tall oil based on solvent extraction and colorimetric analysis, with good reproducibility. We used the developed system to study the effect of the ratio of fatty acids to rosin acids on tall oil separation. When high amounts of rosin acids were present, tall oil recovery was low, while high content of fatty acids above 60% significantly promoted tall oil separation. Therefore, manipulating the content of fatty acids in black liquor before the soap skimming step can significantly affect the tall oil solubility, and hence its separation. The findings open up chemical ways to improve the tall oil yield.
Journal articles
Magazine articles
Causes of poor dregs settling in a green liquor clarifier, TAPPI Journal August 2022
ABSTRACT: A study was conducted to examine the most likely parameters responsible for poor dregs settling at a kraft mill over a 2.5-year period, using multivariate data analysis (MVDA) and machine learning (ML) techniques. The dregs settling behavior seems to be seasonally influenced, implying that wood quality variation can be a factor. The results from the MVDA/ML analysis show that poor dregs settling is correlated to incomplete combustion and/or low load conditions in the recovery boiler, low sulfidity in the causticizing plant, and high flow in the green liquor•weak wash cycle. Compositions of dregs and black liquor were also examined to identify correlations with impaired dregs settling. The results show that poor dregs settling strongly correlates with high silicon (Si) content in dregs and moderately correlates with high iron (Fe) and high aluminum (Al) contents, and with low bulk density in dregs. For mills that experience dregs settling or green liquor filtering issues, regular compositional analyses of dregs, green liquor, weak wash, and black liquor are recommended in order to monitor the dynamics of silicon and other constituents in the recovery cycle.