Search
Use the search bar or filters below to find any TAPPI product or publication.
Filters
Content Type
Publications
Level of Knowledge
Committees
Collections
Journal articles
Pulp bleaching with manganese peroxidase and xylanase: a synergistic effect, TAPPI JOURNAL, October 2000, Vol. 83(10)
Pulp bleaching with manganese peroxidase and xylanase: a synergistic effect, TAPPI JOURNAL, October 2000, Vol. 83(10)
Journal articles
An image analysis method to quantify fibre separation in wood subjected to fatigue loading, TAPPI JOURNAL, December 2000, Vol. 83(12)
An image analysis method to quantify fibre separation in wood subjected to fatigue loading, TAPPI JOURNAL, December 2000, Vol. 83(12)
Journal articles
Application of polyallylamine as a dry strength agent for paper, TAPPI JOURNAL, December 2000, Vol. 83(12)
Application of polyallylamine as a dry strength agent for paper, TAPPI JOURNAL, December 2000, Vol. 83(12)
Journal articles
Pulping of aspen wood in acetic acid media: effect of operating conditions on yield and pulp properties, TAPPI JOURNAL, December 2000, Vol. 83(12)
Pulping of aspen wood in acetic acid media: effect of operating conditions on yield and pulp properties, TAPPI JOURNAL, December 2000, Vol. 83(12)
Journal articles
Case study: power company operates Alabama mill's 'energy island', TAPPI JOURNAL, January 1998, Vol. 81(1)
Case study: power company operates alabama mill's 'energy island', TAPPI JOURNAL, January 1998, Vol. 81(1)
Journal articles
Magazine articles
Recovery boiler back-end heat recovery, TAPPI Journal March 2023
ABSTRACT: Sustainability and efficient use of resources are becoming increasingly important aspects in the operation of all industries. Recently, some biomass-fired boilers have been equipped with increasingly complex condensing back-end heat recovery solutions, sometimes also using heat pumps to upgrade the low-grade heat. In kraft recovery boilers, however, scrubbers are still mainly for gas cleaning, with only simple heat recovery solutions. In this paper, we use process simulation software to study the potential to improve the power generation and energy efficiency by applying condensing back-end heat recovery on a recovery boiler. Different configurations are considered, including heat pumps. Potential streams to serve as heat sinks are considered and evaluated. Lowering the recovery boiler flue gas temperature to approximately 65°C significantly decreases the flue gas losses. The heat can be recovered as hot water, which is used to partially replace low-pressure (LP) steam, making more steam available for the condensing steam turbine portion for increased power generation. The results indicate that in a simple condensing plant, some 1%•4% additional electricity could be generated. In a Nordic mill that provides district heating, even more additional electricity generation, up to 6%, could be achieved. Provided the availability of sufficient low-temperature heat sinks to use the recovered heat, as well as sufficient condensing turbine swallowing capacity to utilize the LP steam, the use of scrubbing and possibly upgrading the heat using heat pumps appears potentially useful.
Journal articles
Magazine articles
Non-process elements in the recovery cycle of six Finnish kraft pulp mills, TAPPI Journal March 2023
ABSTRACT: In this work, the aim was to study the distribution and accumulation of the non-process elements (NPEs) in the recovery cycle of Finnish pulp mills and look at whether the geographical location (North vs. South) correlates with the current Finnish NPE levels. In addition, a comparison to older similar Finnish measurements was made with an attempt to analyze the reasons behind differences in the most typical non-process elements, aluminum (Al), silicon (Si), calcium (Ca), phosphorus (P), magnesium (Mg), manganese (Mn), chlorine (Cl), and potassium (K), taking into account the main elements in the white liquor, sodium (Na) and sulfur (S). The extensive laboratory results gained in this study are from seven sampling points at six pulp mills and present analytical data of metal concentrations. The data obtained presents an update to previous NPE studies. The levels found did not statistically differ between North and South Finland. The NPE levels, apart from phosphorus, found in Finnish pulp mills today have not changed considerably compared to the levels in earlier investigations in the 1990s. In the newest data, the phosphorus concentration was consistently higher in the as fired black liquor, electrostatic precipitator (ESP) ash, lime mud, and green liquor than in the previous results. In addition, the levels of Al, Si, Ca, P, and Mg in recovery boiler ESP ash were consistently higher compared to the older results. As the mills start to close their systems more, a stronger accumulation of NPEs can be expected, increasing the likelihood of more operational problems in the process. Further understanding of where the NPEs accumulate and how they can be most effectively removed will be valuable knowledge in the future.
Journal articles
Magazine articles
Dissolution of wood components during hot water extraction of spruce, TAPPI Journal May 2023
ABSTRACT: The purpose of this study was to investigate the autohydrolysis of softwood, which is the main chemical operation in both hot water extraction and steam explosion. Control of the process and monitoring its course were ensured by the careful choice of experimental setup and conditions: a milled spruce material was extracted in a small flow-through reactor to minimize degradation of the dissolved material and to enable analysis of the resulting liquors extracted at selected time points. The obtained liquid and solid fractions were analyzed for sugar composition and acetic acid concentration. The results showed that partially degraded hemicelluloses were extracted; hemicelluloses side chains were cleaved off and detected as monomers, while deacetylation was limited. Chain scissions of cellulose were observed as a result of autohydrolysis.
Journal articles
Assessing lignin content in Nordic hardwood and softwood species using models based on near-infrared (NIR) spectral data and partial least squares regression (PLSR), TAPPI Journal September 2025
ABSTRACT: Continuous kraft cooking digesters face challenges affecting product quality, making it valuable to improve control through advanced techniques like near-infrared (NIR) spectroscopy, model predictive control, and machine learning models. The primary goal of this study was to use NIR spectra to predict the amount of lignin in hardwood and softwood samples. This study investigated the correlation of NIR derivative spectra with the amounts of lignin relative to other constituents, namely cellulose, hemicellulose, and water, in wood chip samples of varying chip sizes and shapes from six Nordic wood species. It employed partial least squares regression (PLSR) on the NIR data to construct a model that predicted the lignin fraction and the relative fraction of acid-soluble lignin. When trained on a group of five wood species, the model achieved a satisfactory predictive ability, striking a balance between a wide range of lignin content and a consistent chemical environment. The accuracy increased further when the model was restricted only to spruce and pine, reflecting the benefits of a more homogenous dataset. Additionally, the optimal number of latent variables was identified as two, indicating that three distinct chemical components — cellulose, lignin and water — can be effectively differentiated using NIR.
Journal articles
Magazine articles
Evaluation of novel drum chipper technology: pilot-scale production of short wood chips, TAPPI Journal October 2019
ABSTRACT: Impregnation of wood chips with acidic pulping liquors is improved when using short chip lengths. If the average wood chip length is too short, conventional chipping technology will generate excess small material, such as pin chips and fines. The possibility of using newly developed drum chipping technology to produce short-length wood chips was evaluated with a pilot drum chipper operating at different drum velocities and in-feed angles. With a drum velocity of 30 m/s, the average wood chip lengths and the combined fractions of pin chips and fines were 24 mm and 3.3%, 22 mm and 4.2%, and 17 mm and 8.5%. The highest fractions of total accept chips (large and small accepts), 89% to 90% without screening, were observed for drum velocities of 30•34 m/s and average wood chips lengths of 21•22 mm. The results indicate the potential of drum chipping technology for producing short wood chips with relatively high fractions of accept chips and tolerable fractions of pin chips and fines.