Search
Use the search bar or filters below to find any TAPPI product or publication.
Filters
Content Type
Publications
Level of Knowledge
Collections
Journal articles
Magazine articles
Investigation of the influencing factors in odor emission from wet-end white water, TAPPI Journal October 2020
ABSTRACT: Emission of malodorous gases, such as volatile organic compounds (VOCs), hydrogen sulfide (H2S), and ammonia (NH3) during pulping and papermaking has caused certain harm to the air environment and human health. This paper investigated the influencing factors of odor emission from wet-end white water during the production of bobbin paper in a papermaking mill using old corrugated containers (OCC) as raw material. The concentration of malodorous gases emitted from wet-end white water was determined with pump-suction gas detectors. The results indicated that low temperature could limit the release of malodorous gases from white water. Specifically, no total volatile organic compounds (TVOC), H2S, and NH3 was detected at a temperature of 15°C. The concentrations of malodorous gases were slightly increased when temperature increased to 25°C. When temperature was 55°C, the released concentrations of TVOC, H2S, and NH3 were 22.3 mg/m3, 5.91 mg/m3, and 2.78 mg/m3, respectively. Therefore, the content of malodorous gases significantly increased with the temperature increase. The stirring of white water accelerated the release of malodorous gases, and the release rate sped up as the stirring speed increased. However, the total amount of malodorous gases released were basically the same as the static state. Furthermore, the higher the concentration of white water, the greater the amount of malodorous gases released. The pH had little influence on the TVOC release, whereas it significantly affected the release of H2S and NH3. With the increase of pH value, the released amount of H2S and NH3 gradually decreased. When pH reached 9.0, the release amount of H2S and NH3 was almost zero, proving that an alkaline condition inhibits the release of H2S and NH3.
Journal articles
Magazine articles
Characterization of chia plant (Salvia hispanica) for pulping, TAPPI Journal October 2020
ABSTRACT: In this paper, chia plant was characterized in terms of chemical, morphological, and anatomical properties. Chia plant was characterized with low a-cellulose (30.5%); moderate lignin (23.2%) with syringyl to guaiacyl ratio of 1.41; and shorter fiber length (0.67 mm) with thinner cell wall (1.91 µm) and good flexibility coefficient (71.44). Anatomical features showed that chia plant consists of vessels, fibers, parenchyma cells, and collenchyma cells. Chia plant pulping was evaluated in soda-anthraquinone (soda-AQ) and formic acid/peroxyformic acid (FA/PFA) processes. Chia plant was difficult to delignify in the alkaline process. The FA/PFA process produced higher pulp yield at the same kappa number than the soda-AQ process. Unbleached soda-AQ chia pulp exhibited good properties in terms of tensile, bursting, and tearing strengths, even at the unrefined stage, due to high drainability of the pulps. Alkaline peroxide bleached FA/PFA pulp exhibited better papermaking properties and 2% higher brightness than the D0(EP)D1 bleached soda-AQ pulp.
Journal articles
Magazine articles
Recent advances in lignin-based polyurethanes, TAPPI JOURNAL
Recent advances in lignin-based polyurethanes, TAPPI JOURNAL April 2017
Journal articles
Magazine articles
Toward valorization of lignin: characterization and fast pyr
Toward valorization of lignin: characterization and fast pyrolysis of lignin recovered from hot-water extracts of electron-beam irradiated sugar maple, TAPPI JOURNAL April 2017
Journal articles
Magazine articles
Guest Editorial: The next act for nonwovens, TAPPI JOURNAL A
Guest Editorial: The next act for nonwovens, TAPPI JOURNAL August 2017
Journal articles
Magazine articles
Visual discrimination of hygiene tissue softness in the abse
Visual discrimination of hygiene tissue softness in the absence of haptic feedback, TAPPI JOURNAL August 2017
Journal articles
Magazine articles
Modeling the influence of forming fabric structure on vacuum
Modeling the influence of forming fabric structure on vacuum box dewatering, TAPPI JOURNAL August 2017
Journal articles
Magazine articles
Fractional pulping of packaging board in high consistency drum pulping, TAPPI JOURNAL February 2017
Fractional pulping of packaging board in high consistency drum pulping, TAPPI JOURNAL February 2017
Journal articles
Magazine articles
Editorial: Planning for 2017 PEERS Conference: Maximizing success through innovation, TAPPI JOURNAL January 2017
Editorial: Planning for 2017 PEERS Conference: Maximizing success through innovation, TAPPI JOURNAL January 2017
Journal articles
Magazine articles
Physical handsheet properties of pulp furnishes containing attritor-treated fibers, TAPPI JOURNAL January 2017
Physical handsheet properties of pulp furnishes containing attritor-treated fibers, TAPPI JOURNAL January 2017