Search
Use the search bar or filters below to find any TAPPI product or publication.
Filters
Publications
Level of Knowledge
Collections
Journal articles
Magazine articles
Failure Isn’t Just an Option — It’s Unavoidable, Paper360º
Failure Isn’t Just an Option — It’s Unavoidable, Paper360º March/April 2017
Journal articles
Magazine articles
Optical Brightening Agents — Where Next?, Paper360º March/A
Optical Brightening Agents — Where Next?, Paper360º March/April 2017
Journal articles
Magazine articles
Global Study: Most People Highly Value Paper and Print, Pape
Global Study: Most People Highly Value Paper and Print, Paper360º May/June 2017
Journal articles
Magazine articles
TAPPI JOURNAL Summaries, Paper360º November/December 2017
TAPPI JOURNAL Summaries, Paper360º November/December 2017
Journal articles
Magazine articles
Effect of conductivity on paper and board machine performanc
Effect of conductivity on paper and board machine performance— a review and new experiences, TAPPI JOURNAL October 2017
Journal articles
Magazine articles
Polyvinyl alcohol as foaming agent in foam formed paper, TAPPI JOURNAL August 2019
ABSTRACT: The use of polyvinyl alcohol (PVOH or PVA) as a foaming agent in foam formed paper was investigated. Polyvinyl alcohol is a linear, nonionic water-soluble polymer. It has hydrophobic and hydrophilic parts that give it a surface-active character. PVOH is mainly characterized by degree of hydrolysis and molar mass. Degree of hydrolysis is given as mol-% hydroxyl groups on the polymer. Molar mass is measured indirectly by measuring the viscosity of a 4% PVOH solution. The results show that the degree of hydrolysis of PVOH had a strong effect on the foamability of PVOH. Foamability decreased strongly when the degree of hydrolysis increased from 88 to 98 mol-%. The effect of molar mass on foamability was weaker. We saw an increase in foam stability and bubble size with increasing molar mass, but we did not see any effect on maximum air content. PVOH dosage needed to reach >70% air content (F) varied from 2 g/l up to 10.5 g/l, and the lowest addition levels of PVOH needed were achieved with a low molar mass PVOH with a low degree of hydrolysis. The best strength properties were achieved when using fully hydrolyzed PVOH as the foaming agent. Strength properties (both in- and out-of-plane) of samples made using PVOH were better than those made using an anionic foaming agent (sodium dodecyl sulfate, SDS). By adding PVOH binder fibers to the pulp, we were able to further enhance the strength properties of paper and board.
Journal articles
Magazine articles
Real-time monitoring of bubble size distribution in a foam forming process, TAPPI JOURNAL August 2019
ABSTRACT: Foam forming is an intricate option to lessen fiber flocculation and to get better energy and water efficiency when making fiber-based products. Developed during the 1970s, this approach has recently received renewed attention, mainly because it also offers possibilities to widen the fiber-based product portfolios with novel and more valuable products. In addition to air content, bubble size is the most important property of foam. Foam quality control is essential for building real-world foam forming processes. In this work, we show how bubble size can be monitored with direct optical imaging in real time in real process conditions, and how such analysis helps adjust foam quality and discover process faults in foam forming.
Journal articles
Magazine articles
Progress in foam forming technology, TAPPI JOURNAL August 2019
ABSTRACT: This paper summarizes recent developments in foam forming that were mainly carried out in pilot scale. In addition to improving the efficiency of existing processes and allowing better uniformity in material, a wide variety of raw materials can be utilized in foam forming. The focus of this paper is thin webs—papers, boards and foam-laid nonwovens, along with the pilot scale results obtained at VTT in Finland. For paper and board grades, the most direct advantage of foam forming is the potential to produce very uniform webs from longer and coarser fibers and obtain material savings through that. Another main point is increased solids content after a wet press, which may lead to significant energy savings in thermal drying. Finally, the potential to introduce “difficult” raw materials like long synthetic or manmade fibers into a papermaking process enables the manufacturing of novel products in an existing production line. This paper also briefly discusses other interesting foam-based applications, including insulation and absorbing materials, foam-laid nonwovens, and materials for replacing plastics.
Journal articles
Magazine articles
Modeling and parameter optimization of the papermaking processes by using regression tree model and full factorial design, TAPPI Journal February 2021
ABSTRACT: One of the major challenges in the pulp and paper industry is taking advantage of the large amount of data generated through its processes in order to develop models for optimization purposes, mainly in the papermaking, where the current practice for solving optimization problems is the error-proofing method. First, the multiple linear regression technique is applied to find the variables that affect the output pressure controlling the gap of the paper sheet between the rod sizer and spooner sections, which is the main cause of paper breaks. As a measure to determine the predictive capacity of the adjusted model, the coefficient of determination (R2) and s values for the output pressure were considered, while the variance inflation factor was used to identify and eliminate the collinearity problem. Considering the same amount of data available by using machine learning, the regression tree was the best model based on the root mean square error (RSME) and R2. To find the optimal operating conditions using the regression tree model as source of output pressure measurement, a full factorial design was developed. Using an alpha level of 5%, findings show that linear regression and the regression tree model found only four independent variables as significant; thus, the regression tree model demonstrated a clear advantage over the linear regression model alone by improving operating conditions and demonstrating less variability in output pressure. Furthermore, in the present work, it was demonstrated that the adjusted models with good predictive capacity can be used to design noninvasive experiments and obtain.
Journal articles
Magazine articles
Editorial: Agility and adaptation in a dynamic business world, TAPPI Journal January 2021
ABSTRACT: Being agile and adaptive in this current business world is both necessary and beneficial. Throughout last year, we all continued to both directly and indirectly experience the dynamic world where we live. As we wll know, in early 2020 the pandemic gained momentum and has fundamentally altered our daily lives, both personally in how we live and professionally in how we work.