Search
Use the search bar or filters below to find any TAPPI product or publication.
Filters
Content Type
Publications
Level of Knowledge
Committees
Collections
Journal articles
Magazine articles
Evaporation of process water from recycled containerboard mills, TAPPI Journal July 2023
ABSTRACT: The reduction of the specific effluent discharge volumes of paper mills leads to concentrated process waters that are difficult to treat. Evaporation is an effective water reclamation technology; however, its feasibility largely depends on the fouling behavior of the calcium rich process water. A pilot plant study was conducted to investigate fouling of an evaporator processing the production water from a recycled containerboard mill. The evaporator was operated continuously for five weeks at an evaporation temperature of 55°C and a differential temperature of 5°C, and with a recovery rate of approximately 90%. The calcium ion concentration of the circulating liquor exceeded 7,000 mg/L with a pH of 6. Despite the high fouling potential of the circulating liquor, the heat transfer coefficient did not decline over the investigated trial. The absence of deposits on large areas of the heating surfaces demonstrate that the process water does not generally form deposits under the conditions that were investigated. Calcium sulfate deposits were only found in areas where there was inadequate coverage of liquid over the heating surfaces.The findings show that evaporators can be used to effectively close the water system of recycled containerboard mills without fouling impacting the energy efficiency.
Journal articles
Magazine articles
Editorial: Critical literature reviews in open source journals, TAPPI Journal June 2023
ABSTRACT: We stand on the shoulders of giants” is a famous metaphor used by Sir Isaac Newton. This testifies to the fact that new information or discoveries are built on understanding and analyzing earlier information. Particularly in science, technology, engineering, and math (STEM) fields, it is important to have thorough analysis of earlier research activities in a particular field to propose a new direction of research, to evolve new ideas, and to develop new test methods and standards. It is a mandatory and required aspect of every original research paper to have a Literature Review section in the introductory part of the paper.
Journal articles
Magazine articles
Soybean peroxidase treatment of ultra-high kappa softwood pulp to enhance yield and physical properties, TAPPI Journal September 2020
ABSTRACT: The working hypothesis serving as basis for this study is that pulping to a higher kappa number will produce a higher yield pulp, and then treating that pulp with a surface reactive lignin peroxidase to ablate surface lignin will increase specific bonding area. In the present case, the working hypothesis was modified so that soybean peroxidase (SBP) works like lignin peroxidase to modify surface lignin on high-kappa, high-yield softwood pulps to facilitate enhanced fiber-to-fiber bonding such that the resulting paper strength is similar to the lower kappa soft-wood pulp generally used to make linerboard. Soybean peroxidase is actually a plant peroxidase that exhibits lignin peroxidase-like activity. It is not a lignin peroxidase derived from white rot fungus. The current work did show a significant improvement in pulp yield (62.2% vs. 55.2% yield for a 103-kappa control linerboard grade sheet), while treatment with SBP showed that tensile, burst, and STFI properties of the pulp were improved, although more convincing data needs to be obtained.
Journal articles
Magazine articles
Lignin carbohydrate complex studies during kraft pulping for producing paper grade pulp from birch, TAPPI Journal September 2020
ABSTRACT: Paper grade pulp production across the globe is dominated by the kraft process using different lignocellulosic raw materials. Delignification is achieved around 90% using different chemical treatments. A bottleneck for complete delignification is the presence of residual covalent bonds that prevail between lignin and carbohydrate even after severe chemical pulping and oxygen delignification steps. Different covalent bonds are present in native wood that sustain drastic pulping conditions. In this study, 100% birch wood was used for producing paper grade pulp, and the lignin carbohydrate bonds were analyzed at different stages of the kraft cook. The lignin carbohydrate bonds that were responsible for residual lignin retention in unbleached pulp were compared and analyzed with the original lignin-carbohydrate complex (LCC) bonds in native birch wood. It was shown that lignin remaining after pulping and oxygen delignification was mainly bound to xylan, whereas the lignin bound to glucomannan was for the most part degraded.
Journal articles
Magazine articles
Quantification of vegetable oil in recycled paper, TAPPI JOURNAL September 2020
ABSTRACT: Vegetable soybean oil is commonly used in cooking foods that are packaged in takeaway paper-board containers. Vegetable oil is hydrophobic, and in sufficiently high concentration, could interfere with interfiber bonding and result in paper strength loss. In order to quantify the effect of oil on the resulting paperboard strength, it is necessary to quantify the oil content in paper. A lab method was evaluated to determine the soybean oil content in paper. Handsheets were made with pulps previously treated with different proportions of vegetable oil. Pyrolysis gas chromatography-mass spectrometry (pyGCMS) was used to quantify the amount of oil left in the handsheets. The results revealed a strong correlation between the amount of oil applied to the initial pulp and the amount of oil left in the handsheets.In addition, the effect of vegetable oils on paper strength may be affected by the cooking process. Vegetable oil is known to degrade over time in the presence of oxygen, light, and temperature. The vegetable oil was put in an oven to imitate the oil lifecycle during a typical pizza cooking process. The cooked oil was then left at room temperature and not protected from air (oxygen) or from normal daylight. The heated, then cooled, oil was stored over a period of 13 weeks. During this time, samples of the aged oil were tested as part of a time-based degradation study of the cooked and cooled oil.
Journal articles
Magazine articles
Can carbon capture be a new revenue opportunity for the pulp and paper sector?, TAPPI Journal August 2021
ABSTRACT: Transition towards carbon neutrality will require application of negative carbon emission technologies (NETs). This creates a new opportunity for the industry in the near future. The pulp and paper industry already utilizes vast amounts of biomass and produces large amounts of biogenic carbon dioxide. The industry is well poised for the use of bioenergy with carbon capture and storage (BECCS), which is considered as one of the key NETs. If the captured carbon dioxide can be used to manufacture green fuels to replace fossil ones, then this will generate a huge additional market where pulp and paper mills are on the front line. The objective of this study is to evaluate future trends and policies affecting the pulp and paper industry and to describe how a carbon neutral or carbon negative pulp and paper production process can be viable. Such policies include, as examples, price of carbon dioxide allowances or support for green fuel production and BECCS implementation. It is known that profitability differs depending on mill type, performance, energy efficiency, or carbon dioxide intensity. The results give fresh understanding on the potential for investing in negative emission technologies. Carbon capture or green fuel production can be economical with an emission trade system, depending on electricity price, green fuel price, negative emission credit, and a mill’s emission profile. However, feasibility does not seem to evidently correlate with the performance, technical age, or the measured efficiency of the mill.
Journal articles
Magazine articles
Assessing variation in package modeling, TAPPI Journal April 2021
ABSTRACT: Predictions from empirical models are affected by variability in the input parameters for the data set used to build the models. For corrugated boxes, the difference between actual and modeled compression strength creates a real cost associated with box production, often resulting in boxes that may need to be over-designed to compensate for a lack of model precision. No work to date has attempted to assess the limitation in these compression estimates due to input parameter testing variability. In this paper we approach that problem, initially for the McKee equation and then conceptually for other box models. For our industry to do a better job at meeting the needs of our corrugated packaging customers, we need to reduce the variation in the tests we all rely on, particularly for evaluating material strength (edge crush test [ECT]) and package compression performance (box compression test [BCT]).
Journal articles
Magazine articles
Use of fines-enriched chemical pulp to increase CTMP strength, TAPPI Journal April 2021
ABSTRACT: In this study, fines-enriched pulp (FE-pulp)—the fine fraction of highly-refined kraft pulp—was benchmarked against highly-refined kraft pulp (HRK-pulp) as a strength agent in eucalyptus chemithermomechanical pulp (CTMP). Both the FE-pulp and the HRK-pulp were produced from unbleached softwood kraft pulp, and equal amounts of those strength agents were added to the original CTMP, as well as to washed CTMP, where most of the fines had been removed. The effects of the added strength agents were evaluated with laboratory handsheets.The FE-pulp proved to be twice as effective as HRK-pulp. Both HRK-pulp and FE-pulp increased the strength of the CTMP handsheets. The bulk of the handsheets decreased, however, as well as the drainability. The addition of 5% FE-pulp resulted in the same strength increase as an addition of 10% HRK-pulp, as well as the same decrease in bulk and CSF. For the handsheets of washed CTMP, the strengths were not measurable; the CTMP lost the sheet strength when the CTMP-fines content was reduced through washing. The reduced strength properties were compensated for by the addition of chemical pulp fines that proved to be an efficient strength agent. The addition of 5% FE-pulp restored the strength values, and at a higher bulk and higher drainability.
Journal articles
Magazine articles
Formic acid pulping process of rice straw for manufacturing of cellulosic fibers with silica, TAPPI Journal August 2021
ABSTRACT: Emerging technology has the potential to develop entirely new approaches for producing cellulose fiber-based materials along with fuels and chemical raw materials like lignin and furfural. Rice straw is a rich source of cellulosic fibers and inorganic micronic-sized particles termed as ash. They can prove helpful in development of new or enhanced agricultural residue-based materials and products that offer cost effective substitutes for nonrenewable materials used in different domestic and industrial applications. Lignocellulose is an abundant material that is submicronic at the basic level. Rice straw is a fibrous lignocellulosic material obtained as agricultural residue, but it differs from most crop residues in its high content of silicon dioxide (SiO2). Ash content on a dry weight basis ranges from 13% to 20%, varying according to the state of conservation of the straw after harvest. The ash in rice straw has nearly 75% SiO2. The particle size analysis shows variation from a few microns to hundreds of microns for inorganic residues left after burning at high temperatures above 550°C. Proximate analysis of rice straw shows that it contains 54% to 56% holocellulose and 15% to 18% lignin, both of which are natural biopolymers. The compound analysis shows the different compounds present in rice straw ash.Rice straw is available in hundreds of million tons in India and other Asian countries, so suitable technologies are required to convert rice straw from a biomass waste to useful bioproducts like pulp, paper, and paperboard. This research paper is intended to obtain pulp with fibers having inherent silica present in it to give high opacity paper and better bonding between fibers.
Journal articles
Magazine articles
Technological evaluation of Pinus maximinoi wood for industrial use in kraft pulp production, TAPPI Journal August 2021
ABSTRACT: This study characterized Pinus maximinoi wood and evaluated its performance for pulp production. Samples of Pinus taeda wood were used as reference material. For both species, wood chips from 14-year-old trees were used for the technological characterization, pulping, bleaching process analysis, and pulp properties. A modified kraft pulping process was carried out targeting kappa number 28±5% on brownstock pulp. The bleaching sequence was applied for bleached pulp with final brightness of 87±1 % ISO. Refinability and resistance properties were measured in the bleached pulps. Compared to P. taeda wood, P. maximinoi showed slightly higher basic density (0.399 g/cm³) and higher holocellulose (64.5%), lignin (31.1%), and extractives content (4.5%), along with lower ash content (0.16%). P. maximinoi tracheids showed greater wall thickness (6.4 µm) when compared to P. taeda tracheids. For the same kappa number, P. maximinoi and P. taeda resulted in similar screened yield, with an advantage observed for P. maximinoi, which resulted in lower specific wood consumption (5.281 m³/o.d. metric ton), and lower black liquor solids (1.613 metric tons/o.d. metric ton). After oxygen delignification, P. maximinoi pulp showed higher efficiency on kappa reduction (67.2%) and similar bleaching chemical demand as P. taeda pulp. Compared to P. taeda pulps, the refined P. maximinoi pulps had similar results and the bulk property was 10% higher. Results showed that P. maximinoi is an interesting alternative raw material for softwood pulp production in Brazil.