Search
Use the search bar or filters below to find any TAPPI product or publication.
Filters
Content Type
Publications
Level of Knowledge
Committees
Collections
Journal articles
Magazine articles
Comprehensive fault detection and isolation method applied t
Comprehensive fault detection and isolation method applied to a recovery boiler, TAPPI JOURNAL May 2016
Journal articles
Magazine articles
Fundamental molecular characterization and comparison of the O, D0, and E stage effluents from hardwood pulp bleaching, TAPPI Journal 2019
ABSTRACT: The present study characterized effluents from the O, D0, and E stages using nuclear magnetic reso-nance (NMR) and gel permeation chromatography (GPC) techniques to better understand the chemical nature of the dissolved organics formed from the bleaching of a high-yield hardwood kraft pulp. Understanding the structures and molecular weight distribution of these organics is the first step in developing methods to mitigate these contam-inates in the discharged effluents. The results indicated that the molecular weight distribution (MWD) of the dis-solved organics from oxygen delignification effluent is broader than those from D0 and E stage effluents. In addition, the O stage filtrate contained considerable amounts of lignin and xylan fragments, which showed its efficiency in removing such materials. The effluent from the D0 stage contained a lower amount of high molecular weight frag-ments and a higher amount of low molecular weight fragments versus the O-stage filtrate. Aromatic structures were nearly absent in the D0 stage filtrate, but the degraded organic material, presumably from oxidized lignin, contained olefinic (C=C) and carbonyl (C=O) functional groups. Furthermore, higher molecular weight fragments were detected in the E-stage effluent, presumably due to the extensive solubilization and removal of the oxidized lignin generated from the D0 pulp.
Journal articles
Magazine articles
A novel approach for determining the reactivity of dissolving pulp based on the COD method
ABSTRACT: A novel approach for determining the reactivity of dissolving pulp according to the chemical oxygen demand (COD) of water has been discussed. First, a sample of dissolving pulp was subjected to mercerization and xanthation in order to obtain dissolved cellulose fractions. Next, the fractions were digested with a testing solution as applied in COD procedures. Finally, the resulting liquid was rapidly tested by ultraviolet-visible spectrophotometry (UV-Vis). By quantifying the absorbance of Cr3+ at a wavelength of 600 nm, the reactivity of dissolving pulp was indirectly calculated. The results measured by this novel COD method correlated well with the most accepted Fock test results with less than 10% relative difference. Meanwhile, this newly developed COD method required less time-consuming procedures as compared to the Fock test.
Journal articles
Magazine articles
Evaluation of novel drum chipper technology: pilot-scale production of short wood chips, TAPPI Journal October 2019
ABSTRACT: Impregnation of wood chips with acidic pulping liquors is improved when using short chip lengths. If the average wood chip length is too short, conventional chipping technology will generate excess small material, such as pin chips and fines. The possibility of using newly developed drum chipping technology to produce short-length wood chips was evaluated with a pilot drum chipper operating at different drum velocities and in-feed angles. With a drum velocity of 30 m/s, the average wood chip lengths and the combined fractions of pin chips and fines were 24 mm and 3.3%, 22 mm and 4.2%, and 17 mm and 8.5%. The highest fractions of total accept chips (large and small accepts), 89% to 90% without screening, were observed for drum velocities of 30•34 m/s and average wood chips lengths of 21•22 mm. The results indicate the potential of drum chipping technology for producing short wood chips with relatively high fractions of accept chips and tolerable fractions of pin chips and fines.
Journal articles
Magazine articles
Exergy and sensibility analysis of each individual effect in a kraft multiple effect evaporator, TAPPI Journal October 2019
ABSTRACT: The multiple effect evaporator (MEE) is an energy intensive step in the kraft pulping process. The exergetic analysis can be useful for locating irreversibilities in the process and pointing out which equipment is less efficient, and it could also be the object of optimization studies. In the present work, each evaporator of a real kraft system has been individually described using mass balance and thermodynamics principles (the first and the second laws). Real data from a kraft MEE were collected from a Brazilian plant and were used for the estimation of heat transfer coefficients in a nonlinear optimization problem, as well as for the validation of the model. An exergetic analysis was made for each effect individually, which resulted in effects 1A and 1B being the least efficient, and therefore having the greatest potential for improvement. A sensibility analysis was also performed, showing that steam temperature and liquor input flow rate are sensible parameters.
Journal articles
Chemical treatment in mechanical pulping part 4: h2o2 bleaching and pulp property development, TAPPI JOURNAL, January 2001, Vol. 84(1)
Chemical treatment in mechanical pulping part 4: h2o2 bleaching and pulp property development, TAPPI JOURNAL, January 2001, Vol. 84(1)
Journal articles
New insights into dispersed air effects in brownstock washing, TAPPI JOURNAL, January 2001, Vol. 84(1)
New insights into dispersed air effects in brownstock washing, TAPPI JOURNAL, January 2001, Vol. 84(1)
Journal articles
Determination of residual bark in debarked pulpwood using image analysis, TAPPI JOURNAL, January 2001, Vol. 84(1)
Determination of residual bark in debarked pulpwood using image analysis, TAPPI JOURNAL, January 2001, Vol. 84(1)
Journal articles
Comparative papermaking properties of oil-palm empty fruit bunch, TAPPI JOURNAL, January 2001, Vol. 84(1)
Comparative papermaking properties of oil-palm empty fruit bunch, TAPPI JOURNAL, January 2001, Vol. 84(1)
Journal articles
Prioritization for an r&t program: tools that help to achieve consensus, TAPPI JOURNAL, July 2001, Vol. 84(7)
Prioritization for an r&t program: tools that help to achieve consensus, TAPPI JOURNAL, July 2001, Vol. 84(7)