Search
Use the search bar or filters below to find any TAPPI product or publication.
Filters
Content Type
Publications
Level of Knowledge
Committees
Collections
Journal articles
Investigation of the factors contributing to malodorous gases emission during secondary fiber reuse, TAPPI Journal June 2026
ABSTRACT: Malodorous gases are commonly produced during secondary fiber reuse, which is harmful to human health and causes environmental pollution. This paper investigated the influence of fiber type and concentration, temperature, and whitewater concentration on the malodorous gases. The results indicated that, in pulp prepared with fresh water, bleached hardwood kraft pulp (LBKP) did not produce malodorous gases after standing for five days. In contrast, the secondary fiber began to release substantial amounts of total volatile organic compounds (TVOC) on the third day and hydrogen sulfide (H2S) and ammonia (NH3) on the sixth day, and black substances began to appear in the pulp, which proved that the microorganisms began to proliferate. With the increase of the secondary fiber concentration, the release amounts of TVOC, H2S, and NH3 gradually rose, along with the black substances in the pulp. With increased temperature, the release of TVOC increased steadily, while the release of H2S and NH3 reached the maximum at about 45°C, and then began to decline. The decrease of the pulp freeness accelerated the generation of the malodorous gases, but the total release amounts of TVOC, H2S, and NH3 were basically the same. With the increase of white water concentration, the release of TVOC, H2S, and NH3 increased rapidly. When the white water/fresh water was 20 mL/80 mL, the slurry changed from pale yellow to aterrimus on the sixth day. Therefore, microorganisms in the secondary fiber caused pulp deterioration, while white water was the main reason for generating a large amount of malodorous gases.
Journal articles
Permeability simulation for filled paper based on three-dimensional structural model developed by X-ray computed tomography scanning, TAPPI Journal March 2026
ABSTRACT: In this study, an in-depth exploration of filled paper was conducted to understand its structural and permeability characteristics. Cotton linter pulp and precipitated calcium carbonate (PCC) filler were utilized to prepare pure fiber paper, and PCC1 and PCC2 filled papers with different filler particle sizes. Then, the pore structure parameters of paper samples were characterized by mercury intrusion porosimetry, and the X-ray computed tomography (X-CT) scanning was carried out. Subsequently, the 3D microstructures were established based on the X-CT slice images, and the filler characteristic parameters and filler 3D distribution were quantitatively analyzed. Finally, permeation simulations in the thickness and horizontal directions were performed. The findings indicate that filling changes the paper porosity, and the pore tortuosity varies with direction. The estimated pore•throat radius distribution shows specific patterns for different papers. The fillers have different distribution characteristics in the paper samples. Moreover, the paper permeability differs with direction, with smallsized filler having a significant impact on fluid penetration in the thickness direction. Overall, this study provides an effective method for investigating internal paper filler and its distribution, which contributes to the understanding of paper structure•performance relationships.
Journal articles
Moisture performance of silica-paper hybrids in the hygroscopic range, TAPPI Journal March 2026
ABSTRACT: Vapor retarders, crucial in building constructions, are traditionally made from plastic-based materials, raising environmental concerns due to the use of fossil materials. This study explores the potential of functionalized papers, particularly silica-paper hybrids, as sustainable alternatives. This work delves into the moisture properties of sol-gel coated linter papers, considering the water vapor permeability and physisorption behavior following DIN EN ISO 12572 and DIN EN ISO 12571. The study addresses hysteresis, noting the lower hysteresis of mesoporous coatings in comparison to dense coatings and implying benefits in moisture release. Findings underscore the need for a nuanced understanding of coating characteristics and their impact on sorption. In order to better assess the relationship between the coating content of the papers and their specific sorption properties, further investigations, such as the measurement of specific surface properties (e.g., specific surface area), are required. The findings of the water vapor diffusion resistance measurement study demonstrate a correlation between the observed resistance and the vapor levels. The results show that the water vapor diffusion resistance is elevated at lower vapor levels when compared to higher levels. This particular material behavior is typically employed within the construction industry for the utilization of moisture-variable water vapor retarders. The silica-paper hybrids exhibit a response that indicates the potential for advancement into a moisture-variable water vapor barrier.
Journal articles
Effects of in-plane straining on the out-of-plane delamination properties of paperboard, TAPPI Journal March 2026
ABSTRACT: Delamination strength is an essential property for the creasing and folding operations of paperboard into boxes. Due to fixation during creasing, the paperboard suffers in-plane straining. In the present study, we aim to increase our understanding of how in-plane straining affects the delamination properties of paperboard. Samples of paperboard were first strained in in-plane tensile loading, both in the machine-direction and in the cross-direction. Afterward, the paperboard is loaded in the out-of-plane (ZD) direction. Three different grades of commercial paperboard from two major manufacturers were tested in a climate-controlled lab. The results showed similar results for all grades of paperboard, with the delamination strength and the out-of-plane stiffness decreasing virtually linearly with pre-straining. With about 5% plastic in-plane straining, the strength was reduced by about 20% and the stiffness decreased by more than 50% for all grades of paperboard. Normalizing the strength and the stiffness with their values without pre-straining reveals virtually the same relation for all grades of paperboard. If proven to be a general result, this will prove valuable in reducing the demand for experiments.
Journal articles
Modelling of jet impingement in twin-wire paper-machines: Impingement on one fabric, TAPPI JOURNAL, February 2001, Vol. 84(2)
Modelling of jet impingement in twin-wire paper-machines: Impingement on one fabric, TAPPI JOURNAL, February 2001, Vol. 84(2)
Journal articles
A novel multiport cylinder dryer, TAPPI JOURNAL, February 2001, Vol. 84(2)
A novel multiport cylinder dryer, TAPPI JOURNAL, February 2001, Vol. 84(2)
Journal articles
X-ray phase-contrast microscopy of paper, TAPPI JOURNAL, February 2001, Vol. 84(2)
X-ray phase-contrast microscopy of paper, TAPPI JOURNAL, February 2001, Vol. 84(2)
Journal articles
Comparative papermaking properties of oil-palm empty fruit bunch, TAPPI JOURNAL, January 2001, Vol. 84(1)
Comparative papermaking properties of oil-palm empty fruit bunch, TAPPI JOURNAL, January 2001, Vol. 84(1)
Journal articles
Arundo donax l. reed: new perspectives for pulping and bleaching 1. raw material characterisation, TAPPI JOURNAL, January 2001, Vol. 84(1)
Arundo donax l. reed: new perspectives for pulping and bleaching 1. raw material characterisation, TAPPI JOURNAL, January 2001, Vol. 84(1)
Journal articles
Recycling old telephone directories, TAPPI JOURNAL, January 2001, Vol. 84(1)
Recycling old telephone directories, TAPPI JOURNAL, January 2001, Vol. 84(1)