Search
Use the search bar or filters below to find any TAPPI product or publication.
Filters
Content Type
Publications
Level of Knowledge
Committees
Collections
Magazine articles
What does it take to get my paper published?, TAPPI JOURNAL,
What does it take to get my paper published?, TAPPI JOURNAL, March 2002, Vol. 1(1) (62KB)
Journal articles
Magazine articles
Editorial: Multifaceted research at the University of Maine
Editorial: Multifaceted research at the University of Maine, TAPPI JOURNAL September 2017
Journal articles
Magazine articles
Addition of corn stover arabinoxylan into hardwood during pu
Addition of corn stover arabinoxylan into hardwood during pulping for improved physical properties, TAPPI JOURNAL September 2017
Journal articles
Magazine articles
Importance of specimen preparation for edgewise compressive strength (ECT) testing, TAPPI JOURNAL April 2018
Importance of specimen preparation for edgewise compressive strength (ECT) testing, TAPPI JOURNAL April 2018
Journal articles
Magazine articles
Editorial: Douglas Coffin: Paper Physics Guru, TAPPI JOURNAL August 2018
Editorial: Douglas Coffin: Paper Physics Guru, TAPPI JOURNAL August 2018
Journal articles
Magazine articles
Prediction of box failure from paper data for asymmetric corrugated board, TAPPI JOURNAL August 2018
Prediction of box failure from paper data for asymmetric corrugated board, TAPPI JOURNAL August 2018
Journal articles
Magazine articles
Impact of fiber structure on edge-wicking of highly-sized paperboard, TAPPI JOURNAL August 2018
Impact of fiber structure on edge-wicking of highly-sized paperboard, TAPPI JOURNAL August 2018
Journal articles
Magazine articles
Equilibrium moisture content in wet pressing of paper, TAPPI Journal July 2020
ABSTRACT: Equilibrium moisture is a limiting factor in achieving high solids in the later stages of pressing or pressing low basis weight grades. We have developed a model that relates equilibrium moisture directly to the pore size distribution of fibers as measured by the solute exclusion technique. The model shows that chemical pulping and refining increase equilibrium moisture by increasing pore volume at given pore sizes in fibers, which leads to lower pressed solids and greater energy expenditure in the dryer section. Means to increase equilibrium moisture without compromising pulp strength are briefly discussed.
Journal articles
Magazine articles
Combatting lime kiln ringing problems at the Arauco Constitución mill, TAPPI Journal July 2020
ABSTRACT: The lime kiln at the Arauco Constitución mill experienced severe ringing problems requiring it to be shut down for ring removal every 3 to 6 months. The mill controlled the problems by blasting ring deposits off during operation with its existing industrial shotgun and a newly installed Cardox liquid carbon dioxide (CO2) cartridge system. Various ring blasting procedures were tested to determine the optimum ring location and thickness to blast; the optimum depth to insert the CO2 cartridge into the kiln; and the most effective blasting frequency and sequence to employ. The best strategy was found to be the weekly blasting operation that alternated between the liquid CO2 cartridge and the industrial shotgun, with the CO2 cartridge inserted into the ring mass, 20 cm (8 in.) away from the refractory brick surface, and the shotgun aimed at rings at about 28 m (92 ft) from the kiln discharge end. With each blasting event removing considerably more rings than before, it takes a longer time for rings to rebuild, allowing the kiln to run continuously between annual maintenance shutdowns with only a few short (< 4 h) downtimes for ring removal. This substantially reduces the costs associated with ring removal and lime replacement during unscheduled shutdowns.
Journal articles
Magazine articles
Viscoelastic web curl due to storage in wound rolls, TAPPI Journal July 2020
ABSTRACT: Winding is often the final operation in a roll-to-roll manufacturing process. Web materials, i.e., materials that are thin compared to their length, are wound into rolls because this form is the only practical means to store them. The resulting bending strains and associated stresses are large for thick webs and laminates. As many webs are viscoelastic on some time scale, bending stresses lead to creep and inhomogeneous changes in length. When the web material is unwound and cut into discrete samples, a residual curvature remains. This curvature, called curl, is the inability for the web to lie flat at no tension. Curl is an undesirable web defect that causes loss of productivity in a subsequent web process. This paper describes the development and implementation of modeling and experimental tools to explore and mitigate curl in homogenous webs. Two theoretical and numerical methods that allow the prediction of curl in a web are developed: a winding software based on bending recovery theory, and the implementation of dynamic simula-tions of winding. One experimental method is developed that directly measures the curl online by taking advantage of the anticlastic bending resulting from the curl. These methods are demonstrated for a low-density polyethylene web.