Search
Use the search bar or filters below to find any TAPPI product or publication.
Filters
Content Type
Publications
Level of Knowledge
Committees
Collections
Journal articles
Magazine articles
Recovery boiler back-end heat recovery, TAPPI Journal March 2023
ABSTRACT: Sustainability and efficient use of resources are becoming increasingly important aspects in the operation of all industries. Recently, some biomass-fired boilers have been equipped with increasingly complex condensing back-end heat recovery solutions, sometimes also using heat pumps to upgrade the low-grade heat. In kraft recovery boilers, however, scrubbers are still mainly for gas cleaning, with only simple heat recovery solutions. In this paper, we use process simulation software to study the potential to improve the power generation and energy efficiency by applying condensing back-end heat recovery on a recovery boiler. Different configurations are considered, including heat pumps. Potential streams to serve as heat sinks are considered and evaluated. Lowering the recovery boiler flue gas temperature to approximately 65°C significantly decreases the flue gas losses. The heat can be recovered as hot water, which is used to partially replace low-pressure (LP) steam, making more steam available for the condensing steam turbine portion for increased power generation. The results indicate that in a simple condensing plant, some 1%•4% additional electricity could be generated. In a Nordic mill that provides district heating, even more additional electricity generation, up to 6%, could be achieved. Provided the availability of sufficient low-temperature heat sinks to use the recovered heat, as well as sufficient condensing turbine swallowing capacity to utilize the LP steam, the use of scrubbing and possibly upgrading the heat using heat pumps appears potentially useful.
Journal articles
Magazine articles
Non-process elements in the recovery cycle of six Finnish kraft pulp mills, TAPPI Journal March 2023
ABSTRACT: In this work, the aim was to study the distribution and accumulation of the non-process elements (NPEs) in the recovery cycle of Finnish pulp mills and look at whether the geographical location (North vs. South) correlates with the current Finnish NPE levels. In addition, a comparison to older similar Finnish measurements was made with an attempt to analyze the reasons behind differences in the most typical non-process elements, aluminum (Al), silicon (Si), calcium (Ca), phosphorus (P), magnesium (Mg), manganese (Mn), chlorine (Cl), and potassium (K), taking into account the main elements in the white liquor, sodium (Na) and sulfur (S). The extensive laboratory results gained in this study are from seven sampling points at six pulp mills and present analytical data of metal concentrations. The data obtained presents an update to previous NPE studies. The levels found did not statistically differ between North and South Finland. The NPE levels, apart from phosphorus, found in Finnish pulp mills today have not changed considerably compared to the levels in earlier investigations in the 1990s. In the newest data, the phosphorus concentration was consistently higher in the as fired black liquor, electrostatic precipitator (ESP) ash, lime mud, and green liquor than in the previous results. In addition, the levels of Al, Si, Ca, P, and Mg in recovery boiler ESP ash were consistently higher compared to the older results. As the mills start to close their systems more, a stronger accumulation of NPEs can be expected, increasing the likelihood of more operational problems in the process. Further understanding of where the NPEs accumulate and how they can be most effectively removed will be valuable knowledge in the future.
Journal articles
Magazine articles
Paper bending stiffness and web tension measurement from a running web using a vacuum and computer imaging, TAPPI Journal May 2023
ABSTRACT: A novel method for measuring the bending stiffness of paper online during manufacturing is introduced. The method uses photometric stereo imaging to detect the shape of the deflection surface caused by a controllable pressure difference over the paper’s surfaces. The hardware for the measurement is based on a combination of two existing sensors, which has accelerated and facilitated the development of the implementation. The deflection and loads are tied together by the governing differential equation for the bending of an orthotropic elastic plate with selected simplifications. An approach to resolve material parameters and in-plane loads without knowledge of traditional boundary conditions is suggested. The presented method was tested in a paper mill during manufacturing. For bending stiffnesses measured online, correlation coefficients 0.88 and 0.92 were obtained compared to state-of-the-art laboratory measurements. However, the results gained from a moving web are noisy and the data requires correction of the slope and an off-set. Although several issues remain to be resolved before the method can be considered as an accurate measurement for industrial use, the theoretical background, the performance of online implementation, and the results are promising. Possible causes for the observed discrepancies and the future development of the method are discussed.
Journal articles
Magazine articles
Critical parameters for tall oil separation I: The importance of ration of fatty acids to rosin acids, TAPPI Journal September 2019
ABSTRACT: Tall oil is a valuable byproduct in chemical pulping of wood, and its fractions have a large spectrum of applications as chemical precursors, detergents, and fuel. High recovery of tall oil is important for the economic and environmental profile of chemical pulp mills. The purpose of this study was to investigate critical parameters of tall oil separation from black liquor. To investigate this in a controlled way, we developed a model test system using a “synthetic” black liquor (active cooking chemicals OH- and HS- ions), a complete process for soap skimming, and determination of recovered tall oil based on solvent extraction and colorimetric analysis, with good reproducibility. We used the developed system to study the effect of the ratio of fatty acids to rosin acids on tall oil separation. When high amounts of rosin acids were present, tall oil recovery was low, while high content of fatty acids above 60% significantly promoted tall oil separation. Therefore, manipulating the content of fatty acids in black liquor before the soap skimming step can significantly affect the tall oil solubility, and hence its separation. The findings open up chemical ways to improve the tall oil yield.
Journal articles
Magazine articles
A new technique for the measurement of show-through mottle of fine paper, TAPPI Journal September 2019
ABSTRACT: Mottling within print-through and show-through is caused by the variability of the local optical properties of the sheet. This mottling is visually disturbing and a mark of poor paper quality. The ability to predict print-through mottle of printed paper by measuring show-through mottle on the unprinted sheet would be a valuable asset for paper machine control.We examined the relationship between print-through mottle and show-through mottle. We worked with nine samples of 60 lb. uncoated fine paper (90 g/m2), from various North American paper companies, that were printed on an offset press, 400K (400% Black), on both sides. A show-through mottle instrumental determination technique was developed using an existing Fast Fourier Transform-based algorithm. The nine samples examined were ranked similarly by the visual evaluation of print-through mottle and by the instrumental determination of show-through mottle. We thus established that show-through on the unprinted sheet can be used as a reliable predictor of print-through, therefore saving time and money for papermakers. We also found a significant two-sidedness in show-through for some of the samples.
Journal articles
Magazine articles
Creasing severity and reverse-side cracking, TAPPI Journal April 2020
ABSTRACT: Crease cracking can be detrimental to the functionality and appearance of paperboard-based packaging. The effect of creasing severity on the degree of reverse-side crease cracking (bead-side of the crease) of paperboard was investigated. Samples were creased with a range of rule and channel geometries, and the cracking degree was quantified as the percent of cracked length relative to the total length of the crease. The cracking degree was typically below 5% at low crease penetration depths, but was exponentially higher beyond a critical penetration depth. A rule and channel combination with a wider clearance shifted the critical depth to larger values. The creasing severity parameter, termed the creasing draw, converged the cracking degree data from different rule and channel combinations to a single curve. The creasing draw was derived from the same analytical expres-sions as the transverse shear strain and quantifies the length of paper that is drawn into the channel during creasing. The critical draw is defined as the draw at which cracking becomes greater than 5%, which corresponds with the point at which cracking becomes exponential. The critical draw is a material/system parameter that defines the level below which cracking is minimal.
Journal articles
Editorial: Revisiting recycling forums past, TAPPI JOURNAL J
Editorial: Revisiting recycling forums past, TAPPI JOURNAL January 2016
Journal articles
Qualification of Welding Procedures for Duplex Stainless Ste
Qualification of Welding Procedures for Duplex Stainless Steels, 1999 Engineering Conference Proceedings
Journal articles
Steambox Comparator Experiments: Apparatus Validation and In
Steambox Comparator Experiments: Apparatus Validation and Investigation of Steambox Performance, 1999 Engineering Conference Proceedings
Journal articles
Magazine articles
Editorial: Special coating issue contains highlighted works from TAPPICon 2023, TAPPI Journal November 2023
ABSTRACT: Did you know that TAPPI’s Coating and Graphic Arts Division has changed its name to Coating, Printing, and Surface Enhancement (CPSE) Division? This change occurred mid-year, as our members realized that the new name fits much better with the day-to-day workings of the Division, as well as the broader activities to functionalize and add value to paper and paperboard that continue to expand into new arenas.