Search
Use the search bar or filters below to find any TAPPI product or publication.
Filters
Content Type
Publications
Level of Knowledge
Committees
Collections
Journal articles
Magazine articles
Effects of different soda loss measurement techniques on brownstock quality, TAPPI Journal July 2024
ABSTRACT: The efficiency of the kraft recovery plant, bleaching process, and paper machine are affected when black liquor carryover from the brownstock washers is not controlled well. Measuring soda loss within a mill can vary from using conductivity, either in-situ or with a lab sample of black liquor filtrate squeezed from the last stage washer, to measuring absolute sodium content with a lab sodium specific ion probe or spectrophotometer. While measuring conductivity has value in tracking trends in black liquor losses, it is not an acceptable method in reporting losses in absolute units, typically in lb/ton of pulp. This is further complicated when trying to benchmark soda loss performance across a fleet of mills with multiple washer lines. Not only do the testing methods vary, but the amount of bound soda on high kappa pulps can be significant. This variability creates inconsistent results, and studies are needed to understand the effect of different testing methods on the pulp quality. In this study, soda loss is expressed as sodium sulfate (Na2SO4). Four different methods to measure soda content in pulp off commercial brownstock washers were studied: full digestion (FD), washing soaking overnight and washing (WSW), soaking in boiling water and stirring 10-min (SW-10), and squeeze-no wash (Sq). Total, washable, and bound sodium sulfate calculations were determined for each soda content measuring technique using inductively coupled plasma-optical emission spectroscopy (ICP-OES). Results showed bound and washable sodium sulfate amounts significantly depend on which soda measurement technique was used. In addition, the soda results were correlated with the pulp kappa numbers. As the kappa number increases, bound soda increases, regardless of the soda measurement method used. Impacts of high sodium sulfate in brownstock are also discussed.
Journal articles
Magazine articles
A new and quick testing method for evaluating commercial OCC recycled pulp, TAPPI Journal July 2024
ABSTRACT: In this paper, a new and quick testing method for evaluating commercial old corrugated cardboard/containers (OCC) pulp was developed and used by a large Chinese boxboard manufacturer for quality control of imported OCC pulp.
Journal articles
Magazine articles
Editorial: Special pulping and engineering issues of TAPPI Journal yield important recovery cycle research, TAPPI Journal June 2024
ABSTRACT: The June issue of TAPPI Journal, which is dominated by recovery cycle topics, is the last PEERS issue organized by Dr. Peter Hart, the former editor-in-chief who passed away this past May. Peter, who was heavily involved with TAPPI’s Pulp Manufacture Division and various pulping-related committees, also started working with conference technical program planning starting in 2005 with the Engineering, Pulping and Environmental (EPE) Conference, which was the precursor to the more recent Pulping, Engineering, Environmental, Recycling and Sustainability (PEERS) Conference. He was also involved with other conference planning, including that for the International Pulp Bleaching Conference. In addition, Peter was a yearly attendee of such conferences starting as far back as 1990.
Journal articles
Magazine articles
Factors affecting deposit formation in foul condensate stripping systems, TAPPI Journal June 2024
ABSTRACT: In kraft pulp mills, foul condensates are often steam-stripped to produce clean condensate for use as process water. The formation of organic deposits in the stripped condensate is a common problem. A systematic study was conducted to examine the deposit composition and the most likely operating parameters responsible for stripped condensate contamination experienced at a kraft mill in Brazil. Daily averaged data of 170 operating parameters over a 15-month period were analyzed by means of multivariate discriminant analysis and random forest classification analysis. The results showed that the deposit formation is related to high temperature, pressure, and dry solids operations in various evaporator effects. These conditions, combined with the poor demisting efficiency in these effects, may have increased black liquor carryover mist in the vapor. Deposit formation also appeared to be related to increased throughput of the foul condensate stripping system and increased pressure in the stripper. Results of Fourier transform infrared spectroscopy (FTIR) and pyrolysis-gas chromatography mass spectrometry (Py-GCMS) analyses show that the deposit consists of mostly organic matter that likely originated from wood extractives and lignin.
Journal articles
Magazine articles
Understanding the energy and emission implications of new technologies in a kraft mill: Insights from a CADSIM Plus simulation model, TAPPI Journal June 2024
ABSTRACT: Kraft mills play a vital role in energy transition because they have significant potential to reduce their own energy utilization and produce energy/products to decarbonize other sectors. Through biomass combustion and potential biogenic carbon emissions capture, these mills can contribute to offsetting emissions from other sectors. This research investigates the departmental and cross-departmental implications of technology upgrades on energy, steam, emissions, water, and chemicals using a CADSIM Plus simulation model. The model provides a comprehensive analysis of mass and energy balances, offering valuable insights into the benefits and limitations of each technology. The model facilitates scenario analysis and comparisons of process configurations, enabling data-driven decision-making for sustainable and competitive operations. Six high-impact technologies, including additional evaporator effects, weak black liquor membrane concentration, belt displacement washer for brownstock washing, oxygen delignification, and improvements to the pulp machine shoe press and vacuum pumps, are evaluated. Individual technologies resulted in energy savings of 1.2% to 5.4%, biomass consumption reductions of 8.6% to 31.6%, and total emissions reductions of 1.6% to 5.9%. Strategic decision-making must consider existing mill limitations, future technology implementation, and potential production increases. Future research will explore product diversification, biorefineries, and pathways to achieve carbon-negative operations, aiming to reduce emissions and secure a competitive future for kraft mills.
Journal articles
Optimization of energy efficiency and condensate production in evaporation plants for a modern softwood pulp mill, TAPPI Journal April 2026
ABSTRACT: To meet the need to further improve thermal efficiency and environmental performance of kraft pulp mills, new systems and techniques have been developed within the evaporation plant. This paper describes these novel approaches and how they were implemented in a project completed in 2018 for a new evaporator and condensate treatment system supplied by Valmet at the SCA Östrand market pulp mill in Sweden. This project was part of a stepwise upgrade of the complete mill to increase the production capacity of the mill from 430,000 to 900,000 air-dried metric tons/year (ADt/y). As part of this upgrade, the mill had the objectives to increase the energy efficiency of the pulp mill and to minimize the air emissions as much as possible, the effluent volume, and the water usage in the mill. The mill also wanted to have the disposal of the biosludge in the black liquor, and the production of tall oil from black liquor soap, liquid methanol, and turpentine. This required that the new evaporation and condensate treatment system be very closely integrated into the other process departments of the mill, including integration of the hot weak black liquor flash vapor from the digester directly into the evaporator train and the production of multiple streams of clean evaporation plant condensate at the correct temperature for the bleach plant. Heat and mass balance calculation values, which were found to do very well in predicting the effect on actual mill operation, are also presented in this paper.
Journal articles
Utilization of inline total dissolved solids measurement system in a pulp mill's brownstock washing line, TAPPI Journal January 2026
ABSTRACT: Efficient washing improves the recovery of sodium (Na) and sulfur (S) cooking chemicals, as well as wood-based dissolved organic material. It also reduces the additional consumption of chemicals in the subsequent bleaching stages. The operation of the brownstock washing of the pulp mill’s fiber line has a significant impact on the mill’s energy economy, material efficiency, and environmental emissions. Process refractometers can be used to measure the total dissolved solids (TDS) from both the washing liquor and the pulp suspension filtrate part directly from pipelines or pipe bypass loops. In addition, by measuring the three or four incoming/outgoing dissolved solids streams to the washers, together with consistencies and flow rate measurements, it is possible to build the real-time effectiveness calculation of the washer(s). In this work, an online efficiency calculation based on TDS measurements was built for a pressure filter after cooking and oxygen (O2) delignification. The washing performance was monitored over a longer period, and stepwise tests were conducted to find the optimal operating mode. The feed and washing consistencies, the washer’s torque, and the washing liquid distributions varied, and the washer’s efficiency values were monitored using realtime measurements. From the long-term trends of the efficiency calculation, process disturbances could be detected, and their causes could be found. Based on the results of the stepwise tests, an optimal operating model for the washer was found. By optimizing the washing consistency, the Y10 washing yield could be increased. More efficient washing with the same or even a smaller amount of washing liquid can relieve the operation of the evaporator, which is often a bottleneck in the mill. The study also found the effect of cooking-related carryover on the operation of the oxygen stage, as well as differences in the washability of softwood and hardwood.
Journal articles
Towards closed water systems in chemical pulp mills: Evaporation of acidic filtrate from ECF bleaching with high chloride content, TAPPI Journal January 2026
ABSTRACT: In modern bioproducts mills utilizing elemental chlorine-free (ECF) bleaching, the bleaching process is the primary effluent source. The pulp bleaching typically generates 10 m³/a.d. metric ton of acidic filtrate. Despite extensive studies on recycling methods, the acidic filtrate is still typically directed to wastewater treatment plants due to the challenges created by its volume and chloride content. Recently, the volume of acidic filtrate has significantly decreased to 5 m³/a.d. metric ton, reducing the capacity required for the recycling process closer to a feasible level. In this study, we investigated recycling of acidic filtrate by evaporation from the D0 stage of a D0-Eop-D1 bleaching sequence. In the mill, hydrochloric acid (HCl) was used for pH control instead of sulfuric acid (H2SO4) due to better control of precipitation. This arrangement substantially changes the composition of the acidic filtrate, increasing the chloride (Cl-) and decreasing the sulfate (SO4 2-) ionic content. For the above reasons, it is necessary to study the effect of evaporation on the quality of the resulting condensate and concentrate. The results provide new information on how to close water loops in a modern bioproducts mill with higher Cl- content as one option. The results show that the evaporation of the high-chlorine D0 filtrate produces a pure condensate with methanol as the main component. Only small amounts of Cl- were observed in the condensate. The majority of chlorine (Cl) compounds remains as dissolved compounds in the evaporated concentrate when the dry solids content of the concentrate is ~10%. The Cl compounds in the concentrate can be converted to sodium chloride (NaCl) by incineration.
Journal articles
Effects of calcium on sodium salt scaling with the presence of resin acids and fatty acids, TAPPI Journal June 2026
ABSTRACT: Reintroducing tall oil soap or its related products into high dry solids black liquor has been found to reduce sodium salt scaling in falling film evaporators. Aside from resin acids and fatty acids, which are the likely scale inhibitors, calcium is reintroduced into black liquor because of the relatively high calcium content of tall oil soap. One concern is that this increase in calcium content might lead to the formation of additional calcium and sodium scales in evaporators. In this work, we investigated the relationship among trace amounts of calcium, sodium salts, resin acids, and fatty acids in a controlled system using a model salt solution and a benchtop setup. We studied the effects of the calcium carbonate addition and calcium carbonate scales on sodium salt scaling in the presence of resin acids and fatty acids. We found that some calcium carbonate is incorporated in the precipitated sodium crystals, and the suspended sodium crystals become larger and more compact with increasing calcium carbonate concentration. Experiments in the benchtop setup show that precipitating calcium carbonate scale on the heat exchanger does not lead to a higher rate of sodium salt scaling. The solubility of calcium carbonate is not affected by the addition of resin acids and fatty acids. These findings indicate that the reduction in sodium salt scaling through the addition of tall oil soap is primarily related to resin acids and fatty acids, rather than to calcium or to interactions between calcium and mixtures of resin and fatty acids.
Journal articles
Optimization of optical coverage of board surfaces with assessment of light scattering and absorption using mineral as a coating component, TAPPI Journal June 2026
ABSTRACT: One of the primary functions of mineral inclusion into paper or paperboard is to improve the optical performance of the substrate. A coating may be applied to a sheet in order to cover a dark base, to improve the sheet opacity, to give the correct smoothness and gloss, or to give a suitable surface on which to print. The brightness of a pigment has long been used as a guide for pigment choice in paper and board. However, the measured paper brightness is a function of color and light absorption (K) of the coating and base and the light scattering (S) within the sheet resulting from interfaces with different refractive index. The optical performance can be quantified by measuring the S&K coefficients as described by the Kubelka-Munk model/theory in a filled or coated paper sheet. In coating, this is often assessed as a function of coat weight, and the corresponding physical sheet properties are assessed at the same time; for example, the correct gloss, smoothness, point-to-point uniformity, and printability. The optical performance in the sheet is often not directly related to the pigment brightness, but is largely a function of the particle packing within the sheet and coating layer. In the first and second main sections of this work, respectively, we show how S&K calculations from the Kubelka- Munk equations can be used in coated sheets to determine the optical performance and how this can be used as a predictive tool for the final sheet performance. This is presented for base sheets with different starting brightness. The third section of this work focuses on how mineral combinations in coatings can be used to improve the light scattering and consequently the optical performance of the board. We include theoretical considerations and then finally share a case study for improvement on the optical properties of recycled board.