Search
Use the search bar or filters below to find any TAPPI product or publication.
Filters
Content Type
Publications
Level of Knowledge
Committees
Collections
Journal articles
Magazine articles
Degradation of 2,4-dichlorophenol by melamine amine cellulos
Degradation of 2,4-dichlorophenol by melamine amine cellulose- immobilized lacasses, TAPPI JOURNAL October 2017
Journal articles
Magazine articles
Addition of corn stover arabinoxylan into hardwood during pu
Addition of corn stover arabinoxylan into hardwood during pulping for improved physical properties, TAPPI JOURNAL September 2017
Journal articles
Magazine articles
Editorial: Douglas Coffin: Paper Physics Guru, TAPPI JOURNAL August 2018
Editorial: Douglas Coffin: Paper Physics Guru, TAPPI JOURNAL August 2018
Journal articles
Magazine articles
Combustion behavior of kraft black liquor droplets from hot
Combustion behavior of kraft black liquor droplets from hot water pretreated hardwood and softwood chips, November 2016 TAPPI JOURNAL
Journal articles
Magazine articles
Novel CaCO3-polymer nanocomposite fillers for the improvemen
Novel CaCO3-polymer nanocomposite fillers for the improvement of bagasse-based papers, November 2016 TAPPI JOURNAL
Journal articles
Magazine articles
Effects of preincubation on the gelatinization of cassava and corn starch suspensions containing sodium hydroxide as a main component of corrugating adhesives
ABSTRACT: Effects of the preincubation temperature and the caustic-ratio, the molar ratio of sodium hydroxide to starch glucose residue, on the gelatinization of cassava starch and corn starch suspensions were studied using differential scanning calorimetry in view of utilization for corrugating adhesives. The gelatinization temperature and enthalpy change of cassava starch suspensions after the preincubation at 30°C decreased as the caustic-ratio increased, similar to those of corn starch ones: The gelatinization starting temperature (Ts) decreased considerably more than the peak temperature and the conclusion temperature (Tc). Although Ts lowered and the width of gelatinization temperature expanded, compared with those of corn starch suspensions, the two starch suspensions with the same half gelatinization transition temperature showed similar gelatinization characteristics of almost the same Ts and Tc. During 1 h-preincubations at 30°C•50°C, the starch granules with Ts that were lowered considerably below each preincubation temperature by sodium hydroxide showed limited gelatinization. The gelatinization transition did not rapidly spread over the whole suspension, but progressed stepwise in response to the increase of the causticratio and the rise of the preincubation temperature. In a prolonged preincubation at a constant temperature, Ts gradually rose at higher caustic-ratios in which stepwise gelatinization commenced. Although the starch gelatinization was irreversible and not in a stable equilibrium state for a long time, we concluded that such stepwise gelatinization progress controlled the practical preparation and use of corrugating adhesives.
Journal articles
Magazine articles
A novel predictive method for filler coflocculation with cellulose microfibrils, TAPPI Journal November 2019
ABSTRACT: Different strategies aimed at reducing the negative impact of fillers on paper strength have been the objective of many studies during the past few decades. Some new strategies have even been patented or commercialized, yet a complete study on the behavior of the filler flocs and their effect on retention, drainage, and formation has not been found in literature. This type of research on fillers is often limited by difficulties in simulating high levels of shear at laboratory scale similar to those at mill scale. To address this challenge, a combination of techniques was used to compare preflocculation (i.e., filler is flocculated before addition to the pulp) with coflocculation strategies (i.e., filler is mixed with a binder and flocculated before addition to the pulp). The effect on filler and fiber flocs size was studied in a pilot flow loop using focal beam reflectance measurement (FBRM) and image analysis. Flocs obtained with cationic polyacrylamide (CPAM) and benonite were shown to have similar shear resistance with both strategies, whereas cationic starch (CS) was clearly more advantageous when coflocculation strategy was used. The effect of flocculation strategy on drainage rate, STFI formation, ash retention, and standard strength properties was measured. Coflocculation of filler with CPAM plus bentonite or CS showed promising results and produced sheets with high strength but had a negative impact on wire dewatering, opening a door for further optimization.
Journal articles
Magazine articles
Lignin-based resins for kraft paper applications, TAPPI Journal November 2019
ABSTRACT: We investigated miscanthus (MS) and willow (W) lignin-furfural based resins as potential reinforce-ment agents on softwood and hardwood kraft paper. These resins might be sustainable alternatives to the commercial phenolformaldehyde (PF) resins. Phenol is a petrochemical product and formaldehyde has been classified as a carcinogen by the U.S. Environmental Protection Agency. The lignin used in this study was derived from hot water extraction (160ºC, 2 h) of MS and W biomass, and may be considered sulfur-free. These biorefinery lignins were characterized for their chemical composition and inherent properties via wet chemistry and instrumental techniques. The resin blends (MS-resin and W-resin) were characterized for their molecular weight, thermal behavior, and mechanical properties. Mechanical properties were measured by the resin’s ability to reinforce softwood and hard-wood kraft papers. The effect of adding hexamethylenetetramine (HMTA), a curing agent, to the resin was also examined. Mixtures of PF and lignin-based resins were investigated to further explore ways to reduce use of non-renewables, phenol, and carcinogenic formaldehyde. The results show that lignin-based resins have the potential to replace PF resins in kraft paper applications. For softwood paper, the highest strength was achieved using W-resin, without HMTA (2.5 times greater than PF with HMTA). For hardwood paper, MS-resin with HMTA gave the highest strength (2.3 times higher than PF with HMTA). The lignin-based resins, without HMTA, also yielded mechanical properties comparable to PF with HMTA.
Magazine articles
A financial analysis of north american pulp and paper companies, TAPPI JOURNAL, July 2000, Vol. 83(7)
A financial analysis of north american pulp and paper companies, TAPPI JOURNAL, July 2000, Vol. 83(7)
Magazine articles
Global multi-pigment savvy from imerys, TAPPI JOURNAL, June 2000, Vol. 83(6)
Global multi-pigment savvy from imerys, TAPPI JOURNAL, June 2000, Vol. 83(6)