Search
Use the search bar or filters below to find any TAPPI product or publication.
Filters
Content Type
Publications
Level of Knowledge
Committees
Collections
Journal articles
Magazine articles
Addressing production bottlenecks and brownstock washer optimization via a membrane concentration system, TAPPI Journal July 2021
ABSTRACT: Advancements in membrane systems indicate that they will soon be robust enough to concentrate weak black liquor. To date, the economic impact of membrane systems on brownstock washing in kraft mills has not been studied and is necessary to understand the viability of these emerging systems and their best utilization.This study investigated the savings that a membrane system can generate related to brownstock washing. We found that evaporation costs are the primary barrier for mills seeking to increase wash water usage. Without these additional evaporation costs, we showed that our hypothetical 1000 tons/day bleached and brown pulp mills can achieve annual savings of over $1.0 MM when operating at higher dilution factors and fixed pulp production rate. We then investigated the impact of increasing pulp production on mills limited by their equipment. In washer-limited mill examples, we calculated that membrane systems can reduce the annual operating cost for a 7% production increase by 91%. Similarly, in evaporator-limited mill examples, membrane systems can reduce the annual operating cost for a 7% production increase by 86%. These results indicated that membrane systems make a production increase significantly more feasible for these equipment-limited mills.
Journal articles
Magazine articles
Fate of phosphorus in the recovery cycle of the kraft pulping process, TAPPI Journal March 2020
ABSTRACT: The accumulation of nonprocess elements in the recovery cycle is a common problem for kraft pulp mills trying to reduce their water closure or to utilize biofuels in their lime kiln. Nonprocess elements such as magnesium (Mg), manganese (Mn), silicon (Si), aluminum (Al), and phosphorus (P) enter the recovery cycle via wood, make-up chemicals, lime rock, biofuels, and process water. The main purge point for these elements is green liquor dregs and lime mud. If not purged, these elements can cause operational problems for the mill. Phosphorus reacts with calcium oxide (CaO) in the lime during slaking; as a result, part of the lime is unavailable for slaking reactions. The first part of this project, through laboratory work, identified rhenanite (NaCa(PO4)) as the form of P in the lime cycle and showed the negative effect of P on the availability of the lime. The second part of this project involved field studies and performing a mass balance for P at a Canadian kraft pulp mill.
Journal articles
Magazine articles
Synthesis of filtrate reducer from biogas residue and its application in drilling fluid, TAPPI Journal March 2020
ABSTRACT: Biogas residues (BR) containing cellulose and lignin are produced with the rapid development of biogas engineering. BR can be used to prepare the filtrate reducer of water-based drilling fluid in oilfields by chemical modification. BR from anaerobically fermenting grain stillage was alkalized and etherified by caustic soda and chloroacetic acid to prepare filtrate reducer, which was named as FBR. The long-chain crystalline polysaccharides were selected as dispersing agents (DA), and the water-soluble silicate was used as the cross-linking agent. After the hot rolling of FBR in saturated saltwater base mud for 16 h at 120°C, the filtration loss was increased from 7.20 mL/30 min before aging to 8.80 mL/30 min after aging. Compared with the commercial filtrate reducers, FBR had better tolerance to high temperature and salt, and lower cost.
Journal articles
Magazine articles
Lignin-based resins for kraft paper applications, TAPPI Journal November 2019
ABSTRACT: We investigated miscanthus (MS) and willow (W) lignin-furfural based resins as potential reinforce-ment agents on softwood and hardwood kraft paper. These resins might be sustainable alternatives to the commercial phenolformaldehyde (PF) resins. Phenol is a petrochemical product and formaldehyde has been classified as a carcinogen by the U.S. Environmental Protection Agency. The lignin used in this study was derived from hot water extraction (160ºC, 2 h) of MS and W biomass, and may be considered sulfur-free. These biorefinery lignins were characterized for their chemical composition and inherent properties via wet chemistry and instrumental techniques. The resin blends (MS-resin and W-resin) were characterized for their molecular weight, thermal behavior, and mechanical properties. Mechanical properties were measured by the resin’s ability to reinforce softwood and hard-wood kraft papers. The effect of adding hexamethylenetetramine (HMTA), a curing agent, to the resin was also examined. Mixtures of PF and lignin-based resins were investigated to further explore ways to reduce use of non-renewables, phenol, and carcinogenic formaldehyde. The results show that lignin-based resins have the potential to replace PF resins in kraft paper applications. For softwood paper, the highest strength was achieved using W-resin, without HMTA (2.5 times greater than PF with HMTA). For hardwood paper, MS-resin with HMTA gave the highest strength (2.3 times higher than PF with HMTA). The lignin-based resins, without HMTA, also yielded mechanical properties comparable to PF with HMTA.
Conference papers
Recent advances in the commercialization of NIR (near-infrar
ABSTRACT: Near-infrared (NIR) spectroscopy techniques have held the promise of a new generation of online and lab based process analyzers for the pulping and recovery areas for some years now. NIR technology has been shown to be a quite effective method for the analysis of white, green and black liquors by multiple investigators. NIR reflectance techniques have been shown to be effective in predicting yield and kappa number in pulp samples. Recently, commercial analyzers have been developed for green liquor analysis on the dissolving tank, white and green liquor analysis in the recaust area and black liquor analysis on batch and continuous digesters. These analyzers are currently running at different mill sites and are proving to be superior to current technology choices for these applications. A commercial online and lab based yield and kappa number analyzer are currently being developed based on NIR reflectance techniques. Results will be presented on the performance of these analyzers relating to accuracy, maintenance and total installed cost. Other potential NIR applications in the pulping and recovery area will also be addressed.
Journal articles
Environmentally benign psas featured at recycling symposium, TAPPI JOURNAL, February 2000, Vol. 83(2)
Environmentally benign psas featured at recycling symposium, TAPPI JOURNAL, February 2000, Vol. 83(2)
Journal articles
CMP and ctmp of a fast-growing tropical wood: acacia mangium, TAPPI JOURNAL, July 2000, Vol. 83(7)
CMP and ctmp of a fast-growing tropical wood: acacia mangium, TAPPI JOURNAL, July 2000, Vol. 83(7)
Journal articles
Viscosity control - a new way to improve pressure screen performance, TAPPI JOURNAL, September 2000, Vol. 83(9)
Viscosity control - a new way to improve pressure screen performance, TAPPI JOURNAL, September 2000, Vol. 83(9)
Journal articles
Infrared analysis for process control in the pulp and paper industry, TAPPI JOURNAL, October 2000, Vol. 83(10)
Infrared analysis for process control in the pulp and paper industry, TAPPI JOURNAL, October 2000, Vol. 83(10)
Journal articles
Application of polyallylamine as a dry strength agent for paper, TAPPI JOURNAL, December 2000, Vol. 83(12)
Application of polyallylamine as a dry strength agent for paper, TAPPI JOURNAL, December 2000, Vol. 83(12)