Search

Fate of phosphorus in the recovery cycle of the kraft pulping process, TAPPI Journal March 2020

ABSTRACT: The accumulation of nonprocess elements in the recovery cycle is a common problem for kraft pulp mills trying to reduce their water closure or to utilize biofuels in their lime kiln. Nonprocess elements such as magnesium (Mg), manganese (Mn), silicon (Si), aluminum (Al), and phosphorus (P) enter the recovery cycle via wood, make-up chemicals, lime rock, biofuels, and process water. The main purge point for these elements is green liquor dregs and lime mud. If not purged, these elements can cause operational problems for the mill. Phosphorus reacts with calcium oxide (CaO) in the lime during slaking; as a result, part of the lime is unavailable for slaking reactions. The first part of this project, through laboratory work, identified rhenanite (NaCa(PO4)) as the form of P in the lime cycle and showed the negative effect of P on the availability of the lime. The second part of this project involved field studies and performing a mass balance for P at a Canadian kraft pulp mill.

Synthesis of filtrate reducer from biogas residue and its application in drilling fluid, TAPPI Journal March 2020

ABSTRACT: Biogas residues (BR) containing cellulose and lignin are produced with the rapid development of biogas engineering. BR can be used to prepare the filtrate reducer of water-based drilling fluid in oilfields by chemical modification. BR from anaerobically fermenting grain stillage was alkalized and etherified by caustic soda and chloroacetic acid to prepare filtrate reducer, which was named as FBR. The long-chain crystalline polysaccharides were selected as dispersing agents (DA), and the water-soluble silicate was used as the cross-linking agent. After the hot rolling of FBR in saturated saltwater base mud for 16 h at 120°C, the filtration loss was increased from 7.20 mL/30 min before aging to 8.80 mL/30 min after aging. Compared with the commercial filtrate reducers, FBR had better tolerance to high temperature and salt, and lower cost.

Multiple recycling of paperboard: Paperboard characteristics and maximum number of recycling cycles— Part I: Multiple recycling of corrugated base paper, TAPPI Journal November 2019

ABSTRACT: Paper for recycling is an important fiber source for the production of corrugated base paper. The change in production capacity toward more and more packaging papers affects the composition of paper for recy-cling and influences the paper quality. This research project investigated the influence of the multiple recycling of five different corrugated base papers (kraftliner, neutral sulfite semichemical [NSSC] fluting, corrugating medium, testliner 2, and testliner 3) on suspen-sion and strength properties under laboratory conditions. The corrugated board base papers were repulped in a low consistency pulper and processed into Rapid-Köthen laboratory sheets. The sheets were then recycled up to 15 times in the same process. In each cycle, the suspension and the paper properties were recorded. In particular, the focus was on corrugated board-specific parameters, such as short-span compression test, ring crush test, corrugat-ing medium test, and burst. The study results indicate how multiple recycling under laboratory conditions affects fiber and paper properties.

Functional surfaces produced by foam coating, TAPPI JOURNAL

Functional surfaces produced by foam coating, TAPPI JOURNAL August 2016

Acoustic analysis of recovery boiler dissolving tank operati

Acoustic analysis of recovery boiler dissolving tank operation and smelt shattering efficiency, TAPPI JOURNAL September 2016

Fast evaluation of spatial coating layer formation using ultraviolet scanner imaging

Fast evaluation of spatial coating layer formation using ultraviolet scanner imaging, TAPPI JOURNAL August 2015

Recent advances in the commercialization of NIR (near-infrar

ABSTRACT: Near-infrared (NIR) spectroscopy techniques have held the promise of a new generation of online and lab based process analyzers for the pulping and recovery areas for some years now. NIR technology has been shown to be a quite effective method for the analysis of white, green and black liquors by multiple investigators. NIR reflectance techniques have been shown to be effective in predicting yield and kappa number in pulp samples. Recently, commercial analyzers have been developed for green liquor analysis on the dissolving tank, white and green liquor analysis in the recaust area and black liquor analysis on batch and continuous digesters. These analyzers are currently running at different mill sites and are proving to be superior to current technology choices for these applications. A commercial online and lab based yield and kappa number analyzer are currently being developed based on NIR reflectance techniques. Results will be presented on the performance of these analyzers relating to accuracy, maintenance and total installed cost. Other potential NIR applications in the pulping and recovery area will also be addressed.

Södra Deploys First Electric Truck to Transport Pulp from Värö

Bellmer Successfully Closes the Acquisition of Cellwood Machinery AB

The Boxery Launches Sustainable Corrugated Box Range