Search
Use the search bar or filters below to find any TAPPI product or publication.
Filters
Content Type
Publications
Level of Knowledge
Committees
Collections
Journal articles
Magazine articles
Advanced real-time digital microscopy of foaming processes, TAPPI Journal January 2023
ABSTRACT: The properties of aqueous foams play a major role in foam forming and foam coating. Inline real-time foam measurements provide highly desired opportunities for optimization and control of foaming processes. This paper presents inline digital microscopy measurements of aqueous foams in foaming processes. It presents methods for providing detailed information on foam quality parameters, such as foam density and foam homogeneity in real time from the process. In addition, this study evaluates the performance of transillumination and front-light illumination in imaging of foams. The tests show very good results for the transillumination approach. Limitations of the image-based optical technique are discussed, and the precision of bubble size distribution measurement is assessed with a certificated reference substance. The measured foam densities are compared against the reference foam densities in the range 100•300 g/L, providing a linear correlation with R2 value of 0.99. In the case of heterogenous foams with a wide bubble size distribution, the bubble size-dependent dimensionless depth of field must be taken into account to obtain accurate estimates of foam density. Bubble-scale foam homogeneity is described by the standard deviation of bubble size distribution in foam.
Journal articles
Magazine articles
Pareto-based design of experiments for identifying and comparing optimum sealing parameters of heat sealing applications in packaging machines, TAPPI Journal June 2023
ABSTRACT: Sealing is one of the most important process steps in industrial packaging, because the sealed seam is the most sensitive section of a package in terms of quality. For this reason, a major focus in flexible packaging is the sealing process, and among this, heat sealing is the most frequently used technology. In detail, applications of heat sealing processes are confronted with four conflicting objectives: increasing seam quality, reducing dwell time, reducing sealing temperature, and increasing process robustness towards varying conditions. Typical problems, such as identification of the optimum process parameters or selection of the most appropriate packaging film, are subject to these conflicting objectives.This paper presents a recently published design of experiments for characterizing and comparing heat sealing properties of packaging films based on a multi-objective optimization algorithm. The approach provides easy-to-read charts showing all optimum sealing parameters with regard to the four essential objectives of heat sealing: seam quality, dwell time, sealing temperature, and process robustness. Three case studies show exemplary applications of the new approach: 1) analyzing transport damages of beverage powder packages; 2) identifying and comparing optimum sealing parameter of a standard, mono-material, and fiber based packaging film regarding tightness and visual properties of the produced sachets; and 3) analyzing the effect of additional aluminum layers on sealing characteristics regarding hot-tack.The new design of experiments may provide the basis of a standard test method for the identification of optimal sealing parameters in the heat sealing processes.
Journal articles
Magazine articles
Creating adaptive predictions for packaging-critical quality parameters using advanced analytics and machine learning, TAPPI Journal November 2019
ABSTRACT: Packaging manufacturers are challenged to achieve consistent strength targets and maximize pro-duction while reducing costs through smarter fiber utilization, chemical optimization, energy reduction, and more. With innovative instrumentation readily accessible, mills are collecting vast amounts of data that provide them with ever increasing visibility into their processes. Turning this visibility into actionable insight is key to successfully exceeding customer expectations and reducing costs. Predictive analytics supported by machine learning can provide real-time quality measures that remain robust and accurate in the face of changing machine conditions. These adaptive quality “soft sensors” allow for more informed, on-the-fly process changes; fast change detection; and process control optimization without requiring periodic model tuning.The use of predictive modeling in the paper industry has increased in recent years; however, little attention has been given to packaging finished quality. The use of machine learning to maintain prediction relevancy under ever-changing machine conditions is novel. In this paper, we demonstrate the process of establishing real-time, adaptive quality predictions in an industry focused on reel-to-reel quality control, and we discuss the value created through the availability and use of real-time critical quality.
Journal articles
Pre-damping effects on water absorption and drying dynamics in flexographic printing, TAPPI Journal November 2025
ABSTRACT: Optimizing flexographic printability can involve the ink and the substrate, as well as the printing process. It has been widely reported in the literature that controlling topography of the substrate and its porosity are vital for good flexographic printability, especially when using water-based inks. This study focuses on how pre-damping a surface impacts liquid absorption and improves wet trapping (ink on ink with no intermediate drying) in flexographic printing. A Prüfbau universal print tester was adapted to analyze flexographic wet-on-wet ink printing and trapping using yellow and magenta inks for contrast. Slow drying of the first ink layer (yellow) leads to mottle when the second layer (magenta) is applied. The study explores the “wet sponge” hypothesis: a pre-damped surface should absorb liquid faster. The Lucas- Washburn equation describes long-term absorption, but it does not capture short-term uptake, which instead follows a linear dependence on time.
Journal articles
Magazine articles
Predicting strength characteristics of paper in real time using process parameters, TAPPI Journal March 2022
ABSTRACT: Online paper strength testing methods are currently unavailable, and papermakers have to wait for manufacture of a complete reel to assess quality. The current methodology is to test a very small sample of data (less than 0.005%) of the reel to confirm that the paper meets the specifications. This paper attempts to predict paper properties on a running paper machine so that papermakers can see the test values predicted in real time while changing various process parameters. This study was conducted at a recycled containerboard mill in Chicago using the multivariate analysis method. The program provided by Braincube was used to identify all parameters that affect strength characteristics. Nearly 1600 parameters were analyzed using a regression model to identify the major parameters that can help to predict sheet strength characteristics. The coefficients from the regression model were used with real-time data to predict sheet strength characteristics. Comparing the prediction with test results showed good correlation (95% in some cases). The process parameters identified related well to the papermaking process, thereby validating the model. If this method is used, it may be possible to predict various elastic moduli (E11, E12, E22, etc.) in the future as the next step, rather than the traditional single number “strength” tests used in the containerboard industry, such as ring crush test (RCT), corrugating medium test (CMT), and short-span compression strength test.
Journal articles
The influence of precoating layers on the performance of water-based barrier coatings, TAPPI Journal January 2025
Cellulose nanofibrils (CNF) on paper have been demonstrated to be an effective barrier against oxygen and grease and have been shown to improve the barrier performance of dispersion-based barrier coatings. The potential to produce paper grades that have good oxygen, grease, and moisture barrier properties is clear, but a better understanding of the synergies between CNF, other coating layers, and water-based barrier coatings (WBBC) is needed to optimize these systems. Different coat weights of a commercial WBBC were applied to papers that have a range of different qualities and thicknesses of CNF precoating layers. The same WBBC was also applied to pigmented coated paper, with various types of pigments and latex levels. Samples were characterized in terms of grease resistance, water vapor transmission rate (WVTR), and oxygen transmission rate (OTR) before and after folding. The results were contrasted to cases where the WBBC was applied to the paper with no precoating layer. When the WBBC is applied on a CNF layer or the pigmented coating layer, the performance of the WBBC for the water vapor barrier improves a significant amount compared to when the WBBC is applied to the base paper with no precoating layer. This improvement likely comes from these precoating layers filling in the large paper pores, which leads to the WBBC forming a continuous layer at low coat weights. Folding decreases the moisture barrier performance to some degree, but the grease resistance is not influenced by folding when a CNF precoating layer is involved. Oxygen barrier properties are moderate for the CNF layer alone and are less than 5 cm3/m2/day when WBBC is coated on the CNF layer. This result likely comes from the barrier coating’s ability to repair defects in the CNF layer to stop the easy passage of oxygen in defect regions of the sample.
Journal articles
Effect of xylan on the mechanical performance of softwood kraft pulp 2D papers and 3D foams, TAPPI Journal March 2025
ABSTRACT: Pulp fibers are paramount in paper products and have lately seen emerging use in fiber foams. Xylan, an integral component in pulp fibers, is known to contribute to paper strength, but its effect on the strength of pulp fiber foams remains less explored. In this study, we investigate the role of xylan in both 2D handsheets and 3D foams. For a softwood kraft pulp, we enzymatically removed 1% from pulp fibers and added 3% xylan to them by adsorption, corresponding to approximately a decrease of a tenth and an increase of a third of the total xylan content. The mechanical properties of 2D fiber networks, i.e., handsheets, made using the xylan-enriched pulp improved, particularly regarding tensile strength and Young’s modulus; however, the decrease in mechanical properties of handsheets made from enzymatically- treated xylan-depleted pulp was more pronounced. In 3D networks • pulp fiber foams, much less fiber-fiber contacts formed, and thus the mechanical properties were not as much influenced by removal of xylan. Furthermore, the presence of the required surfactant on the fibers, acting as debonding agent, overshadows any positive effect xylan might have on fiber-fiber bonding. We propose that the improved mechanical properties for the sheets result from a combination of an increased number of fiber-fiber bonds and higher sheet density, while the deterioration in mechanical properties of handsheets comprising enzymatically-treated fibers is caused by the opposite effect.
Journal articles
Magazine articles
Numerical investigation of the effect of ultrasound on paper drying, TAPPI Journal March 2022
ABSTRACT: The paper drying process is very energy inefficient. More than two-thirds of the total energy used in a paper machine is for drying paper. Novel drying technologies, such as ultrasound (US) drying, can be assessed numerically for developing next-generation drying technologies for the paper industry. This work numerically illustrates the impact on drying process energy efficiency of US transducers installed on a two-tiered dryer section of a paper machine. Piezoelectric transducers generate ultrasound waves, and liquid water mist can be ejected from the porous media. The drying rate of handsheet paper in the presence of direct-contact US is measured experimentally, and the resultant correlation is included in the theoretical model. The drying section of a paper machine is simulated by a theoretical drying model. In the model, three scenarios are considered. In the first scenario, the US modules are positioned in the dryer pockets, while in the second scenario, they are placed upstream of the drying section right after the press section. The third case is the combination of the first and second scenarios. The average moisture content and temperature during drying, enhancement of total mass flux leaving the paper by the US mechanism, total energy consumption, and thermal effect of heated US transducers are analyzed for all cases. Results show that the application of the US can decrease the total number of dryer drums for drying paper. This numerical study is based on the US correlation obtained with the US transducer direct-contact with the paper sample. Thus, future work should include US correlation based on a non-contact US transducer.
Journal articles
Magazine articles
Furnishing autohydrolyzed poplar weakly alkaline P-RC APMP to make lightweight coated base paper, TAPPI Journal February 2022
ABSTRACT: This work investigated the effects of autohydrolysis pretreatment severity on poplar (Populus tomentosa Carr.) woodchips used to make a type of high-yield pulp (HYP) known as preconditioning followed by refiner chemical treatment, alkaline peroxide mechanical pulp (P-RC APMP). It also investigated the ratios for partially replacing sodium hydroxide (NaOH) with magnesium oxide (MgO) in the high-consistency (HC) retention stage of the P-RC APMP process on the obtained HYP’s properties. The results show that the pretreatment severity of autohydrolysis at combined hydrolysis factor (CHF) = 10.77 and the 50 wt% ratio for partially substituting NaOH with MgO were the optimum conditions for making light-weight coated (LWC) base paper. Compared to the conventional P-RC APMP, the optimized P-RC APMP had similar bulk and higher tensile, burst, and tear indices, as well as opacity, but a slightly lower ISO brightness. When the optimized P-RC APMP and commercial softwood bleached sulfate pulp (SBKP) were blended to make LWC base paper, the most favorable pulp furnish was comprised of 50% optimized P-RC APMP and 50% commercial SBKP. The obtained LWC base paper handsheet had better bulk, and its other properties could also meet the require-ments of LWC base paper.
Journal articles
Magazine articles
Upscaling of foam forming technology for pilot scale, TAPPI JOURNAL August 2019
ABSTRACT: The need for production cost savings and changes in the global paper and board industry during recent years have been constants. Changes in the global paper and board industry during past years have increased the need for more cost-efficient processes and production technologies. It is known that in paper and board production, foam typically leads to problems in the process rather than improvements in production efficiency. Foam forming technology, where foam is used as a carrier phase and a flowing medium, exploits the properties of dispersive foam. In this study, the possibility of applying foam forming technology to paper applications was investigated using a pilot scale paper forming environment modified for foam forming from conventional water forming. According to the results, the shape of jet-to-wire ratios was the same in both forming methods, but in the case of foam forming, the achieved scale of jet-to-wire ratio and MD/CD-ratio were wider and not behaving sensitively to shear changes in the forming section as a water forming process would. This kind of behavior would be beneficial when upscaling foam technology to the production scale. The dryness results after the forming section indicated the improvement in dewatering, especially when foam density was at the lowest level (i.e., air content was at the highest level). In addition, the dryness results after the pressing section indicated a faster increase in the dryness level as a function of foam density, with all density levels compared to the corresponding water formed sheets. According to the study, the bonding level of water- and foam-laid structures were at the same level when the highest wet pressing value was applied. The results of the study show that the strength loss often associated with foam forming can be compensat-ed for successfully through wet pressing.