Search
Use the search bar or filters below to find any TAPPI product or publication.
Filters
Content Type
Publications
Level of Knowledge
Committees
Collections
Journal articles
Magazine articles
Model development for real oxygen delignification processes, TAPPI Journal October 2024
ABSTRACT: Previous extensive work has been done on modeling the oxygen delignification process, based on how the basic parameters, i.e., temperature, kappa number, concentration of alkali, and concentration of oxygen, affect the delignification rate. However, these models are not used extensively to evaluate the performance of real processes, primarily because they have not been able to properly consider all the essential issues affecting delignification in practice. Such issues include the mass transfer and consumption of oxygen, which defines the concentration of dissolved oxygen in the process, and the effect of that concentration on the delignification rate. In this paper, a new way to model the oxygen delignification process is used in which these parameters, among other smaller matters, are taken into account. The basic model and its parameters were defined by the information obtained from the literature, delignification made in the laboratory tests, and mill processes and mill tests. An essential aspect of these studies was the information obtained from the oxygen concentration measured in the residual gas obtained from the top of the reactor. With the aid of this measurement, it was possible to define more accurately the consumption of oxygen and partial pressure of oxygen that define the concentration of dissolved oxygen in the reactor. Using mill experiments, a model was formed that predicts the operation of the oxygen delignification process. The model was used to show how much the process could be improved by optimizing the charge of the oxygen. The mill experiments also confirmed that mass transfer of oxygen is modeled correctly enough, except when the charge of oxygen is very low and/or the mixing is not efficient enough. In that case, there is variation in the concentration of oxygen in the process that should be taken into account in the modeling.
Journal articles
Magazine articles
Optimizing OCC refining with defloccing, TAPPI Journal April 2025
ABSTRACT: Subjecting pulp to a high shear zone immediately after refining results in more efficient refining. This phenomenon was originally observed to benefit softwood pulp refining. It was attributed to floc reduction based on floc measurements in mill refiners and the observation of reduced headbox plugging. Hence, this phenomenon has been termed “defloccing.” The present work shows this technology also benefits refining of North American old corrugated containers (OCC). The combined results of several mill trials with OCC defloccing demonstrate the interactions between OCC refining intensity, defloccing technology, and other state-of-the-art refining improvements. At the same refining intensity, defloccing OCC on 100% recycled machines increases OCC refining efficiency by 15%, with greater efficiency improvement on machines that use softwood as well as OCC. Furthermore, it is shown that the benefits of defloccing are additive to refining improvements made in the refining zone of a refiner plate. Most OCC refiner plate designs can therefore benefit from the addition of a defloccing feature.
Journal articles
Conversion of paper-grade pulp from rice straw into dissolving pulp, TAPPI Journal June 2025
ABSTRACT: About 1,165 million metric tons of rice straw is generated every year worldwide, which can be a good source for the circular bioeconomy. In this research paper, the paper-grade pulp from rice straw was converted to dissolving-grade pulp by fractionation in a biorefinery initiative. Rice straw was cooked at an optimum condition of 8% potassium hydroxide (KOH) charge for 120 min at 150°C and produced a pulp yield of 47.2% with a kappa number of 18.5. Subsequently, D0(EP)D1 bleaching was carried out for the produced pulp, and the brightness of the pulp reached to 82.4%. From the black liquor, 16.5% of the lignin and 11.9% of the hemicellulose were isolated for producing biobased products and chemicals, and then the spent liquor was used for soil amendment. The bleached pulp was fractionated in a Bauer McNett fiber classifier. The pulp fibers retained on 16-, 30-, and 50-mesh screens were used as a longer fiber fraction pulp, and pulp fibers retained on 100- and 200-mesh screens were used as a shorter fiber pulp. The longer and shorter fiber fraction pulps were analyzed for cellulose, R10, pentosan, and viscosity. The long fiber fraction pulps were characterized by higher cellulose (88.2% vs. 83.1%) and lower pentosan (11.3% vs. 13.0%) content than the shorter fiber fraction pulps. The longer fiber fraction was further treated with cold KOH to remove residual hemicellulose. The KOH extraction reduced pentosan content in pulp to 6.3% and increased á-cellulose content to 91.3%. The short fiber fraction was converted to monomeric sugars using cellulase enzymes with varying reaction time, temperature, and consistency. The efficiency of cellulase activity was assessed through glucose yield and residual dry weight. A temperature of 45°C, 5.0 pH, 5% consistency, and 6 filter paper units/gram (FPU/g) o.d. pulp resulted in maximum sugar conversion of 85.7%.
Journal articles
Magazine articles
Black liquor evaporator upgrades— life cycle cost analysis, TAPPI Journal March 2021
ABSTRACT: Black liquor evaporation is generally the most energy intensive unit operation in a pulp and paper manufacturing facility. The black liquor evaporators can represent a third or more of the total mill steam usage, followed by the paper machine and digester. Evaporator steam economy is defined as the unit mass of steam required to evaporate a unit mass of water from black liquor (i.e., lb/lb or kg/kg.) The economy is determined by the number of effects in an evaporator train and the system configuration. Older systems use four to six effects, most of which are the long tube vertical rising film type. Newer systems may be designed with seven or even eight effects using falling film and forced circulation crystallization technology for high product solids. The median age of all North American evaporator systems is 44 years. Roughly 25% of the current North American operating systems are 54 years or older. Older systems require more periodic maintenance and have a higher risk of unplanned downtime. Also, older systems have chronic issues with persistent liquor and vapor leaks, shell wall thinning, corrosion, and plugged tubes. Often these issues worsen to the point of requiring rebuild or replacement. When considering the age, technology, and lower efficiency of older systems, a major rebuild or new system may be warranted. The intent of this paper is to review the current state of black liquor evaporator systems in North America and present a basic method for determining whether a major rebuild or new installation is warrant-ed using total life cycle cost analysis (LCCA).
Journal articles
Ozone-enhanced bleaching of softwood kraft pulp, TAPPI JOURNAL August 2010
Ozone-enhanced bleaching of softwood kraft pulp, TAPPI JOURNAL August 2010
Journal articles
CFD-Based Modeling of Kraft Char Beds â?¢ Part 2: A Study on the Effects of Droplet Size and Bed Shape on Bed Processes, TAPPI JOURNAL February 2010
CFD-Based Modeling of Kraft Char Beds • Part 2: A Study on the Effects of Droplet Size and Bed Shape on Bed Processes, TAPPI JOURNAL February 2010
Journal articles
Busting Vacuum System Myths, Part 2, Frontline Focus, Volume 6, Issue 1
Frontline Focus, January 2010
Journal articles
Can't Stand the Heat?, Frontline Focus, Volume 6, Issue 2
Frontline Focus, February 2010
Journal articles
The Challenge of Coal Ash, Paper360° September/October 2014
The Challenge of Coal Ash, Paper360º September/October 2014
Journal articles
TechLink: Inside Tappi Journal
TAPPI JOURNAL Summaries, Paper360º September/October 2014