Search
Use the search bar or filters below to find any TAPPI product or publication.
Filters
Publications
Level of Knowledge
Collections
Journal articles
Magazine articles
Effects of rings on flow and temperature in lime kilns, TAPPI Journal June 2022
ABSTRACT: A steady state, two-dimensional (2D) axisymmetric model has been developed to help understand how rings form and grow in a typical lime kiln. Rings of varying length, thickness, and geometry at the front and back faces were modeled to study the effects on flue gas flow and temperature. The results show that ring growth causes the gas velocity to increase and insulates the adjacent refractory, resulting in a lower kiln shell temperature. The results also reveal the formation of recirculation zones immediately down-stream of the rings, as well as temperature deviations upstream and downstream of the rings that might promote recarbonation and further ring growth. The model was applied to a kiln from a kraft mill with front-end and mid-kiln rings and good agreement was obtained between the measured and predicted kiln shell temperatures, providing confidence in the modeling.
Journal articles
Magazine articles
Web instability in the open draw and the impact on paper machine efficiency, TAPPI Journal May 2022
ABSTRACT: Paper is most likely to break in the first open draw on a paper machine where it is unsupported, wettest, and weakest. Tension is applied to peel the web from the roll surface, as well as minimize web flutter in the open draw. The average tension is well below the breaking point and is often set by adjusting the speed difference between the press and the next machine element by visually observing the behavior of the web. However, machine direction variations caused by instabilities in the paper machine can cause tension swings that exceed the strength of the web. Measurement of the web’s release point from press rolls on pilot and commercial paper machines was used to identify the cause of tension instabilities. Variations in the speed of the paper machine drives and the work of adhesion from the press roll surface were identified as key factors. Fluctuations of paper moisture, which affects the elastic modulus and strength of the web, appear to be less important.
Journal articles
Magazine articles
How do mud balls form in lime kilns?, TAPPI Journal April 2023
ABSTRACT: Mud ball formation in lime kilns has been a persistent problem in many kraft mills, particularly for older kilns that are equipped with chains. A systematic laboratory study was conducted to examine how mud balls are formed and the key factors that affect ball formation. The results confirm the general mill experience that high moisture and high sodium contents in lime mud are the main contributing factors to ball formation. The high moisture content allows lime mud to agglomerate and grow to form balls, while the high sodium content helps make the balls hard and retain their shape. A ball formation mechanism is proposed to explain how mud balls form and grow near the kiln feed end.
Journal articles
Magazine articles
Improved deinking and stickies removal
Improved deinking and stickies removal, TAPPI JOURNAL November 2017
Journal articles
Magazine articles
Editorial: Planning for 2017 PEERS Conference: Maximizing success through innovation, TAPPI JOURNAL January 2017
Editorial: Planning for 2017 PEERS Conference: Maximizing success through innovation, TAPPI JOURNAL January 2017
Journal articles
Magazine articles
Modeling of the energy of a smelt-water explosion in the recovery boiler dissolving tank, TAPPI Journal August 2020
ABSTRACT: The explosion energy generated as molten smelt droplets interact with water was evaluated as a function of smelt distribution, water temperature, and smelt temperature using a thermodynamic model. The results show that increasing smelt-to-water volume ratio and water temperature significantly increases the explosion energy, converting a larger proportion of the thermal energy of smelt into mechanical work. To reduce the chance of violent smelt-water explosions, it is important to: i) optimize the shatter jet design and operation to uniformly distribute the smelt over a large area in the dissolving tank; ii) avoid high green liquor temperature and ensure adequate liquor mixing; and iii) avoid upsets that may cause heavy smelt runoff or jellyroll smelt.
Journal articles
Magazine articles
Editorial: Let's talk tissue!, TAPPI Journal July 2019
ABSTRACT: In this issue of TAPPI Journal (TJ), researchers Olejnik and Pelczynski of Lodz University of Technology in Poland and researcher Bloch of the University of Gre-noble Alpes in France use an experimental device to measure the liquid absorption properties of tissue (p. 417). The device, called the eXtended liquid penetration analyzer (XLPA), was initially built at the Institute of Papermaking and Printing at the University of Lodz. Results from the study published here showed that the XLPA measurements were in good agreement with the ISO 12625:-8:2010 standard measurements. The researchers believe this method could ultimately help mills characterize the liquid absorption of their tissue in a better and faster manner.
Journal articles
Magazine articles
Effects of metal surface morphology on deposition behavior of microstickies from papermaking white water, TAPPI Journal July 2023
ABSTRACT: Deposition of small adhesive particles, called microstickies, onto pulp processing equipment and paper machines causes quality and operational problems for recycling mills. The factors that control deposition of microstickies onto surfaces of metal parts remain unclear. In this work, aluminum surfaces with a range of surface roughness were exposed to slurries containing microstickies. The deposition results showed that flat surfaces promote the aggregation and deposition of microstickies particles. Uneven surfaces tended to favor deposition of smaller microstickies, 0.2•1 µm, which may be related to greater contact area presented by the rougher surface. This work provides insights into the deposition of microstickies.
Journal articles
Magazine articles
Editorial: Surface energy in printing is the focus of runner-up, TAPPI Journal May 2024
ABSTRACT: The runner-up to the 2023 TAPPI Journal Best Re-search Paper was “Surface energy considerations for offset printing of coated paper and pa-perboard,” co-authored by Janet Pres-ton, Andrew Findlay, Jonathan Keen, and Eli Gaskin of Imerys Minerals in Par, England, UK. Their research appeared in the November 2023 special coating issue organized by TAPPI Journal Editorial Board Members Steve Ottone, Gregg Reed, and Greg Welsch.
Journal articles
Magazine articles
Determining operating variables that impact internal fiber bonding using Wedge statistical analysis methods, TAPPI Journal November 2021
ABSTRACT: In this study, Wedge statistical analysis tools were used to collect, collate, clean up, plot, and analyze several years of operational data from a commercial paper machine. The z-direction tensile (ZDT) and Scott Bond tests were chosen as representative of fiber bond strength. After analyzing thousands of operational parameters, the ones with the most significant impact upon ZDT involved starch application method, starch penetration, and the amount of starch applied. Scott bond was found to be significantly impacted by formation and refining. Final calendering of the paper web has also shown an impact on internal fiber bonding.