Search
Use the search bar or filters below to find any TAPPI product or publication.
Filters
Content Type
Publications
Level of Knowledge
Committees
Collections
Journal articles
Magazine articles
Enhancement of processability, surface, and mechanical properties of paper based on rice straw pulp using biopolymers for packaging applications, TAPPI Journal July 2019
ABSTRACT: wo biopolymers, chitosan and oxidized starch, were used as wet-end additives to improve the strength properties of the paper because of their biodegradable and non-hazardous qualities. The present study reports the improvement in surface and strength properties of packaging-grade paper made with rice straw pulp using biopolymers, chitosan, oxidized starch, and surface sizing added at the wet end of the paper machine.Use of chitosan at all doses from 0.5 to 10 kg/ton enhanced important surface and strength properties of paper. The breaking length, tear index, burst index, ring crush strength, stretch, tensile energy absorption index, and Taber stiff-ness of the paper with 10 kg/ton of chitosan as a wet-end additive showed 22%, 14%, 20%, 59%, 16%, 44%, and 48% improvement, respectively, in comparison to control, (i.e, without its addition). The Cobb60 was also reduced by 45%, showing better resistance to water in comparison to rice straw paper alone. The effects of chitosan added at the wet end on the paper surface were investigated using Fourier transform infrared spectroscopy (FTIR). The use of 10 kg/ton of chitosan at the wet end reduced the color and total suspended solids in the back water of the papermak-ing system by 55% and 51%, respectively. Further enhancement in the surface and strength properties of paper was observed following surface sizing with oxidized starch.
Journal articles
Magazine articles
The sticky behavior of pulp and paper mill biosludge during drying, TAPPI Journal June 2019
ABSTRACT: Pulp and paper mill biosludge becomes sticky after being dried to a certain solids content. As bio-sludge becomes sticky, it agglomerates and adheres to the heat transfer surfaces of the dryer. This undesirable property can lower the dryer efficiency and cause the drying equipment to fail.A systematic study was conducted to examine the sticky behavior of biosludge. The stickiness was evaluated by measuring the adhesive force between a sludge cake and a stainless steel substrate, and the cohesive force between a sludge cake and a sludge substrate. The results show that: i) both adhesive and cohesive forces increase markedly as the solids content increases, reaching a maximum value at about 13% solids, and then decrease steadily at a high-er solids content; ii) cohesive force is stronger than adhesive force, implying that biosludge tends to agglomerate rather than adhere to smooth equipment surfaces; and iii) mixing wood fines or fly ash from a biomass boiler reduc-es the stickiness of the mixture. These findings may help mills improve the thermal efficiency of biosludge dryers and to turn biosludge into a more attractive fuel for burning in biomass boilers.
Journal articles
Magazine articles
Fabrication of cross-linked starch-based nanofibrous mat with optimized diameter, TAPPI JOURNAL June 2019
ABSTRACT: The design and synthesis of natural and synthetic polymer blends have received recent and wide attention. These new biomaterials exhibit progress in properties required in the field of medicine and healthcare. Herein, the aim of present study is to fabricate starch (ST)/polyacrylic acid (PAA) electrospun nanofibrous mat with a smooth and uniform morphology, lowest fiber diameter (below 100 nm) and the highest possible starch content. Starch itself is poor in process-ability, and its electrospinning could be quite a challenging process. To address this, we carried out the response surface methodology (RSM) technique for modelling the electrospinning process. In order to have ST/PAA nanofibers with the finest possible diameter, optimized processing parameters (applied volt-age, nozzle-collector distance and feed rate) obtained from RSM technique were applied. ST/PAA electrospun nano-fibers with an average diameter of 74±13 nm were successfully achieved via the electrospinning method for the first time. The structure, preparation and properties of the nanofibrous structure were discussed. Results indicated that drug loaded ST/PAA blend nanofibrous structure has a great potential to be used in controlled drug release systems.
Journal articles
Magazine articles
A study of the softness of household tissues using a tissue softness analyzer and hand-felt panels, TAPPI Journal March 2019
ABSTRACT: This study applied the reciprocal matrix approach to deduce the correlation between hand-felt (HF) and tissue softness analyzer (TSA) instrumental measurements of tissue softness. The research was conducted in three phases, which are discussed separately. In the phase one study, results indicated that systematic collection of samples and preparation of test specimens were the foundation of successful tests. TSA-HF and tensile strength exhibited a strong negative correlation. In the future, same-unit physical properties can provide a basis for discuss-ing the commonality and complementary natures of hand-felt and TSA softness measurements. In phase two, through the reciprocal matrix approach, subjective softness assessments performed by humans were reliably quan-tified. The quantified values were further applied to a statistical analysis using the t-test to distinguish and train pro-fessional panelists. In phase three of HF panel test results, all independent panels were compared to one another under a uniform scale established by four standard samples. The calibrated HF panel values were incorporated with TSA-HF results to establish technical curves between the softness and tensile strength, which were helpful for onsite workers to carry out process controls.
Journal articles
Magazine articles
Creating adaptive predictions for packaging-critical quality parameters using advanced analytics and machine learning, TAPPI Journal November 2019
ABSTRACT: Packaging manufacturers are challenged to achieve consistent strength targets and maximize pro-duction while reducing costs through smarter fiber utilization, chemical optimization, energy reduction, and more. With innovative instrumentation readily accessible, mills are collecting vast amounts of data that provide them with ever increasing visibility into their processes. Turning this visibility into actionable insight is key to successfully exceeding customer expectations and reducing costs. Predictive analytics supported by machine learning can provide real-time quality measures that remain robust and accurate in the face of changing machine conditions. These adaptive quality “soft sensors” allow for more informed, on-the-fly process changes; fast change detection; and process control optimization without requiring periodic model tuning.The use of predictive modeling in the paper industry has increased in recent years; however, little attention has been given to packaging finished quality. The use of machine learning to maintain prediction relevancy under ever-changing machine conditions is novel. In this paper, we demonstrate the process of establishing real-time, adaptive quality predictions in an industry focused on reel-to-reel quality control, and we discuss the value created through the availability and use of real-time critical quality.
Journal articles
Magazine articles
Evaluation of novel drum chipper technology: pilot-scale production of short wood chips, TAPPI Journal October 2019
ABSTRACT: Impregnation of wood chips with acidic pulping liquors is improved when using short chip lengths. If the average wood chip length is too short, conventional chipping technology will generate excess small material, such as pin chips and fines. The possibility of using newly developed drum chipping technology to produce short-length wood chips was evaluated with a pilot drum chipper operating at different drum velocities and in-feed angles. With a drum velocity of 30 m/s, the average wood chip lengths and the combined fractions of pin chips and fines were 24 mm and 3.3%, 22 mm and 4.2%, and 17 mm and 8.5%. The highest fractions of total accept chips (large and small accepts), 89% to 90% without screening, were observed for drum velocities of 30•34 m/s and average wood chips lengths of 21•22 mm. The results indicate the potential of drum chipping technology for producing short wood chips with relatively high fractions of accept chips and tolerable fractions of pin chips and fines.
Journal articles
Magazine articles
Effects of different ammonium lignosulfonate contents on the crystallization, rheological behaviors, and thermal and mechanical properties of ethylene propylene diene monomer/polypropylene/ammonium lignosulfonate composites, TAPPI Journal January 2020
ABSTRACT: Thermoplastic elastomer (TPE), made from ethylene propylene diene monomer (EPDM) and polypropylene (PP) based on reactive blending, has an excellent processing performance and characteristics and a wide range of applications. However, there are currently no reports in the literature regarding the usage of TPE in making composite boards. In this paper, EPDM, PP, and ammonium lignosulfonate (AL) were used as the raw materials, polyethylene wax was used as the plasticizer, and a dicumyl peroxide vulcanization system with dynamic vulcanization was used to make a new kind of composite material. This research studied the influences of the AL contents on the crystallization behaviors, rheological properties, thermal properties, and mechanical properties of the composites. The results showed that the AL content had a noticeable impact on the performance of the composite board. Accordingly, this kind of composite material can be used as an elastomer material for the core layer of laminated flooring.
Journal articles
Magazine articles
Alternative “green” lime kiln fuels: Part II—Woody biomass, bio-oils, gasification, and hydrogen, TAPPI Journal May 2020
ABSTRACT: This paper is the second of a two-part series on “green” lime kiln fuels. The first part of this work reviews the use of pulp mill and recovery byproducts as either full or partial replacement of oil or natural gas in the kiln. The second part reviews the use of various forms of woody biomass, bio-oils, gasification and hydrogen as potential carbon neutral or carbon-free lime kiln fuels. Several of these options require specialized burners to supply the fuel to the kiln and high-quality metallurgy to withstand the acidic conditions of the fuel.
Journal articles
Magazine articles
Guest Editorial: Coating research addresses new product demands in response to global pandemic, TAPPI Journal November 2020
ABSTRACT: For all of us, the year 2020 has been one of significant challenge. Our communities, companies, institutions, organizations, and families have had to make many tough decisions and change our way of life as a result of the global pandemic.
Journal articles
Magazine articles
Kraft recovery boiler operation with splash plate and/or beer can nozzles — a case study, TAPPI Journal Octobr 2021
ABSTRACT: In this work, we study a boiler experiencing upper furnace plugging and availability issues. To improve the situation and increase boiler availability, the liquor spray system was tuned/modified by testing different combinations of splash plate and beer can nozzles. While beer cans are typically used in smaller furnaces, in this work, we considered a furnace with a large floor area for the study. The tested cases included: 1) all splash plate nozzles (original operation), 2) all beer can nozzles, and 3) splash plate nozzles on front and back wall and beer cans nozzles on side walls. We found that operating according to Case 3 resulted in improved overall boiler operation as compared to the original condition of using splash plates only. Additionally, we carried out computational fluid dynamics (CFD) modeling of the three liquor spray cases to better understand the furnace behavior in detail for the tested cases. Model predictions show details of furnace combus-tion characteristics such as temperature, turbulence, gas flow pattern, carryover, and char bed behavior. Simulation using only the beer can nozzles resulted in a clear reduction of carryover. However, at the same time, the predicted lower furnace temperatures close to the char bed were in some locations very low, indicating unstable bed burning. Compared to the first two cases, the model predictions using a mixed setup of splash plate and beer can nozzles showed lower carryover, but without the excessive lowering of gas temperatures close to the char bed.