Search
Use the search bar or filters below to find any TAPPI product or publication.
Filters
Publications
Level of Knowledge
Collections
Journal articles
Magazine articles
An analytical approach to assess the interrelation of surface properties and softness of tissue paper, TAPPI Journal February 2023
ABSTRACT: The tissue industry constantly strives for improving the overall quality of tissue paper, as customers pay more attention to special quality features when it comes to a purchase decision between different products. As producers need to optimize their processes and furnish mixtures to keep production costs low, accurate and fast methods are crucial for characterization of important tissue properties. Here, we present a method for the characterization of the tissue surface regarding roughness and describe its relation to the tissue surface softness properties, based on a sample set of dry-creped bath tissue (DCT) with different amounts of softwood (SW), hardwood (HW), and nonwood pulp (NWP). The surface of tissue is complex and consists of several overlying structural features; thus, the optical non-contact measurement principle of focus variation was used to provide robust and reliable topographical surface information. Based on the obtained 3D data, areal surface analysis was performed to determine the surface roughness of the tissue samples, which is described by the developed interfacial areal ratio (Sdr) and the power spectral density (PSD). To determine the surface softness properties (TS7) of the tissue, a widely-used tissue softness analyzer (TSA) in the industry was employed. The surface softness (TS7) and the stiffness (D) parameters of this instrument were considered for surface and structural characterization. The results of the surface roughness (Sdr and PSD) and surface softness TS7 measurements show a good linear correlation, with higher surface roughness implying a higher TS7. The presented evaluation of these aspects of tissue softness allows an objective, fast, and accurate assessment of the relevant properties in addition to standard panel tests and is also applicable to other hygiene products.
Journal articles
Magazine articles
Experimental study and prediction of two-phase flow pattern distribution diagrams in multi-channel cylinder dryer, TAPPI Journal July 2023
ABSTRACT: The multi-channel cylinder dryer (MCD) is designed to improve heat transfer. Although there are numerous research studies on the pressure drop, heat transfer characteristics, and flow pattern in static state of MCD, there is little research on the flow pattern in the rotating state. In this paper, the distribution of flow pattern in MCD under different rotating speeds and steam mass flow rates is studied. Furthermore, the logistic regression method (LR) is used to predict the flow pattern diagrams. The results show that in the front section of the flow channel, the flow pattern is basically annular flow, which is not affected by mass flow rate and rotating speed. On the other hand, wavy flow, vortex flow, slug flow, and bubble flow can be observed when the fluid enters the middle and the end section. The higher the rotating speed and the steam mass flow rate, the more the flow pattern tends to be an annular and wavy flow. At the end of the passage, the flow pattern is mainly slug flow. The predicted flow pattern diagrams are in good agreement with the experimental result, and to obtain an effective flow pattern in the middle and the end section of the flow channel, the influence of increasing rotating speed is greater than that of increasing steam mass flow rate. However, the specific rotating speed, steam mass flow rate, and other parameters should still be set by combining with the actual situation. This work can provide some references for the further study of MCD flow characteristics.
Journal articles
Magazine articles
Techno-economic analysis of hydrothermal carbonization of pulp mill biosludge, TAPPI Journal March 2023
ABSTRACT: For many mills, the biosludge from wastewater treatment is difficult to recycle or dispose of. This makes it a challenging side stream and an important issue for chemical pulping. It often ends up being burned in the recovery or biomass boiler, although the moisture and non-process element (NPE) contents make it a problematic fuel. Biosludge has proven resistant to attempts to reduce its moisture. When incinerated in the biomass boiler, the heat from dry matter combustion is often insufficient to yield positive net heat. Mixing the sludge with black liquor in the evaporator plant for incineration in the recovery boiler is more energy efficient, but is still an additional load on the evaporator plant, as well as introducing NPEs to the liquor. In this study, treating the biosludge by hydrother-mal carbonization (HTC), a mild thermochemical conversion technology, is investigated. The HTC process has some notable advantages for biosludge treatment; taking place in water, it is well suited for sludge, and the hydrochar product is much easier to dewater than untreated sludge. In this study, two HTC plant designs are simulated using IPSEpro process simulation software, followed by economic analysis. Low temperature levels are used to minimize investment costs and steam consumption. The results show that if the sludge is incinerated in a biomass boiler, payback periods could be short at likely electricity prices. The HTC treatment before mixing the sludge with black liquor in the evaporator plant is profitable only if the freed evaporator capacity can be used to increase the firing liquor dry solids content.
Journal articles
Magazine articles
Functionalization of wood/plant-based natural celluslose fibers with nanomaterials: a review, TAPPI JOURNAL February 2018
Functionalization of wood/plant-based natural celluslose fibers with nanomaterials: a review, TAPPI JOURNAL February 2018
Journal articles
Magazine articles
Print quality of flexographic printed paperboard related to coating composition and structure, TAPPI Journal January 2018
Print quality of flexographic printed paperboard related to coating composition and structure, TAPPI Journal January 2018
Journal articles
Magazine articles
Understanding the pulping and bleaching performances of eucalyptus woods affected by physiological disturbance, TAPPI Journal November 2018
Understanding the pulping and bleaching performances of eucalyptus woods affected by physiological disturbance, TAPPI Journal November 2018
Journal articles
Magazine articles
Regulatory and sustainability initiatives lead to improved polyaminopolyamide-epichlorohydrin (PAE) wet-strength resins and paper products, TAPPI JOURNAL September 2018
Regulatory and sustainability initiatives lead to improved polyaminopolyamide-epichlorohydrin (PAE) wet-strength resins and paper products, TAPPI JOURNAL September 2018
Journal articles
Magazine articles
Cracking at the fold in double layer coated paper: the influence of latex and starch composition, TAPPI Journal February 2019
Cracking at the fold in double layer coated paper: the influence of latex and starch composition, TAPPI Journal February 2019
Journal articles
Magazine articles
Synthesis and characterization of novel foams by pyrolysis of lignin, TAPPI Journal January 2019
Synthesis and characterization of novel foams by pyrolysis of lignin, TAPPI Journal January 2019
Journal articles
Magazine articles
In-process detection of fiber cutting in low consistency ref
In-process detection of fiber cutting in low consistency refining based on measurement of forces on refiner bars, TAPPI JOURNAL April 2017